LG Electronics 55LS460E manual Securing the TV to a wall optional, Depending on model

Page 19

ASSEMBLING AND PREPARING 19

Caution

Securing the TV to a wall (optional)

(Depending on model)

y yDisconnect the power first, and then move

 

or install the TV. Otherwise electric shock

 

may occur.

 

y yIf you install the TV on a ceiling or slanted

 

wall, it may fall and result in severe injury.

 

Use an authorized LG wall mount and contact

 

the local dealer or qualified personnel.

 

y yDo not over tighten the screws as this may

 

cause damage to the TV and void your

 

warranty.

 

y yOnly use screws and wall mounts that meet

 

the VESA standard. Any damages or injuries

 

by misuse or using an improper accessory

 

are not covered by the warranty.

 

y yOn the 47LT**** models, Use M6 x L45

 

screws. Wall mount screw is not provided

 

when purchased with TV and wallmount

 

[LSW400B (G)]. Screw M6 x L45 can be

 

used after separate purchase.

1 Insert and tighten the eye-bolts, or TV brackets

 

 

and bolts on the back of the TV.

NOTE

y yUse screws that are listed on the VESA standard screw specifications.

y yThe wall mount kit includes an installation manual and necessary parts.

y yThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.

y yThe length of screws may differ depending on the wall mount. Make sure to use the proper length.

y yFor more information, refer to the manual supplied with the wall mount bracket.

y yWhen attaching a third-party wall mounting bracket to the TV, insert the wall mount inner spacers into the TV wall mount holes to move your TV in vertical angle. Please make sure not to use the spacers for LG wall mounting bracket. (For 55LS460E)

-If there are bolts inserted at the eye-bolts position, remove the bolts first.

2Mount the wall brackets with the bolts to the wall.

Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3Connect the eye-bolts and wall brackets tightly with a sturdy rope.

Make sure to keep the rope horizontal with the flat surface.

CAUTION

y yMake sure that children do not climb on or hang on the TV.

NOTE

y yUse a platform or cabinet that is strong and large enough to support the TV securely.

y yBrackets, bolts and ropes are optional. You can obtain additional accessories from your local dealer.

ENGLISH

Wall Mount Inner Spacer

Image 19
Contents LED LCD TV English Important Safety InstructionsYyProtect the power cord from being walked on YyANTENNAS Outdoor antenna grounding Can differ by country YyDISCONNECTING Device from the Main PowerYyCleaning YyGroundingFor USA and Canada YyDot DefectYyGenerated Sound Preventing Image burn or Burn-in on your TV screenOpen Source Software Notice LicensesTable of Contents Assembling and Preparing Installation ProcedureUnpacking Stand Screws Desk-mount Screw Cable holder Power Cord holderAC/DC Adapter Protection cover For LT560E series Spacers Optional Extras For LT560E, LS460E seriesAN-WF100 Rear Connection panel For 32/37/42LT560C, 32/37/42/47LT560E Parts and buttonsFor LT560C, LT560E series Side Connection panel InputPanel For LS460E series Screen Side Connection panelSpeakers Rear ConnectionAttaching the stand Setting up the TVScreen from scratches Top ViewFor 55LS460E Stand Body M4 x Front Stand Base EnglishMounting on a table Attaching the TV to a desk Wall Mount Inner Spacer YDisconnect the power first, and then moveSecuring the TV to a wall optional Depending on modelTidying cables External Speaker Out Number button Remote ControlDash Color buttons OK/ENTER ꔉBack Exit ꕯFor 32/37/42/47LT560E, 55LS460E General TroubleshootingSymptom Possible Causes Possible Solutions Display Panel Picture47LT560E-UA SpecificationsResolution Horizontal Vertical RGBPC, Hdmi PC supported modeRS-232C External Control Device SetupRS-232C Setup Type of connector D-Sub 9-Pin MaleSet ID Set ID number RS-232C configurationsWire Configuration Serial female-female Null modem cable Wire ConfigurationsNot standardCommunication Parameters Transmission / Receiving protocol Command1Command2 Set ID DataCrCommand2 Set ID OKDatax Command2 Set ID NGDataxVolume Mute Command k e Power Command k aInput Select Command x b Aspect Ratio Command k cBass Command k s To adjust bass OSD Select Command k lRemote Control Lock Mode Command k m Treble Command k r To adjust trebleChannel Tuning Command m a Energy Saving Command j qAuto Configuration Command j u Channel Add/Del Command m b Key Command m cMain/Sub Two/One Using Table List Channel TuningStep Child Safety LG Customer Information Center