APPENDIX
APPENDIX
01. Power (Command2:a)
To control Power On/Off of the TV.
Transmission [k][a][ | ][Set ID][ ][Data][Cr] |
Data 0 : Power Off | Data 1 : Power On |
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
*In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function.
*Note: In this model, TV will send the Acknowledge after power on processing completion.
There might be a time delay between command and acknowledge.
02.Input Select (Command2:b) (Main Picture Input) To select input source for the TV.
Transmission [k][b][ ][Set ID][ ][Data][Cr]
Data 0: DTV | Data 1: Analog |
Data 2: AV1 | Data 3: AV2 |
Data 4: Component 1 | Data 5: Component 2 |
Data 6: | Data 7: HDMI1 |
Data 8: HDMI2 | Data 9: HDMI3 |
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
03. Aspect Ratio (Command2:c) (Main picture format) To adjust the screen format.
You can also adjust the screen format using the RATIO button on remote control or in the Picture menu.
Transmission [k][c][ | ][Set ID][ ][Data][Cr] |
Data 1: 4:3 | 4: Zoom 1 |
2: 16:9 | 5: Zoom 2 |
| 6: Set by program |
Reserved
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
04.Screen Mute (Command2:d) To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 0 : Screen mute off (Picture on)
Data 1 : Screen mute on (Picture off) Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Mute (Command2:e)
To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute on (Volume off)
Data 1 : Volume mute off (Volume on) Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
06.Volume Control (Command2:f) To adjust volume.
You can also adjust volume with the volume buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64
Refer to ‘Real data mapping 1’ as shown below. Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
07.Contrast (Command2:g) To adjust screen contrast.
You can also adjust contrast in the Picture menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64
*Refer to ‘Real data mapping 1’ as shown below. Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
08.Brightness (Command2:h)
To adjust screen brightness.
You can also adjust brightness in the Picture menu. Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64(*transmit by Hexadecimal code) *Refer to ‘Real data mapping 1’ as shown below. Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
*Real data mapping 1 0 : Step 0
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100