LG Electronics 42PC5D, 32LC7D owner manual Set ID OK/NGDatax

Page 91

01. Power (Command2:a)

To control Power On/Off of the TV.

Transmission [k][a][ ][Set ID][ ][Data][Cr]

Data 0 : Power Off Data 1 : Power On Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]

*In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function.

*In this model, TV will send the Acknowledge after power on processing completion.

*There might be a time delay between command and acknowledgement.

02.Input Select (Command2:b) (Main Picture Input) To select input source for the TV.

Transmission [k][b][ ][Set ID][ ][Data][Cr]

Data 0: DTV

Data 5: Component 2

Data 1: Analog

Data 7: RGB-PC

Data 2: AV1

Data 8: HDMI1/DVI

Data 3: AV2

Data 9: HDMI2

Data 4: Component 1

 

 

 

Acknowledgement [b][

][Set ID][ ][OK/NG][Data][x]

03. Aspect Ratio (Command2:c) (Main picture format) To adjust the screen format.

You can also adjust the screen format using the RATIO button on remote control or in the Option menu. Transmission [k][c][ ][Set ID][ ][Data][Cr]

Date 1: 4:3

5:

Zoom 2

2: 16:9

6:

Set by program

3:Horizon

4:Zoom 1

Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]

04.Screen Mute (Command2:d) To select screen mute on/off.

Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 0 : Screen mute off (Picture on)

Data 1 : Screen mute on (Picture off) Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]

05. Volume Mute (Command2:e) To control volume mute on/off.

You can also adjust mute using the MUTE button on remote control.

Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume mute on (Volume off) Data 1 : Volume mute off (Volume on) Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]

06. Volume Control (Command2:f) To adjust volume.

You can also adjust volume with the volume buttons on remote control.

Transmission [k][f][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

Refer to ‘Real data mapping’ as shown below. Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]

07.Contrast (Command2:g) To adjust screen contrast.

You can also adjust contrast in the Video menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64

Refer to ‘Real data mapping’ as shown below. Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]

08.Brightness (Command2:h) To adjust screen brightness.

You can also adjust brightness in the Video menu. Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64(*transmit by Hexadecimal code) Refer to ‘Real data mapping’ as shown below. Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]

09. Color (Command2:i)

To adjust the screen color.

You can also adjust color in the Video menu.

Transmission [k][i][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

Refer to ‘Real data mapping’ as shown below.

Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]

*Real data mapping 0 : Step 0

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

63 : Step 99 (SET ID 99)

64 : Step 100

*Tint : R50 ~ G50

*Balance : L50 ~ R50

APPENDIX

89

Page 90 Page 92
Image 91
Page 90 Page 92
Contents 37LC7D 50PC5D 42LC7D 32LC7D 42PC5DPage FCC Notice Important Safety Instructions Safety InstructionsDo not use this apparatus near water Exposed to dripping or splashing and no Use only with the cart, stand, tripod, bracketGrounding Contents External Control Through RS-232C Time SettingIntroduction Feature of this TVPreparation AccessoriesFront Panel Controls Front Panel InformationPlasma TV Model LCD TV Model Remote Control SensorBack Connection Panel Back Panel InformationHere shown may be somewhat different from your TV Video ServiceComponent AV OUTBack Cover for Wire Arrangement Connect the cables as necessary How to remove the Cable ManagementEnsure the eye-bolts or brackets are tightened securely Attaching the TV to a WallStand Installation Only 32/37 inches LCD TV models Vesa Wall Mounting Desktop Pedestal InstallationPlasma TV Model LCD TV Model Antenna Analog or Digital Antenna or Cable ConnectionHow to use External Equipment SetupHD Receiver Setup How to connectTurn on the digital set-top box External Equipment SetupExternal Equipment Setup Refer to the DVD players manual for operating instructions DVD SetupComponent Input ports Connect the video outputs Y, PB, PR of the DVD toVideo input on the set Select AV1 input source by using the Input button onRemote control Connect the S-VIDEO output of the DVD toWhen connecting with an antenna VCR SetupInsert a video tape into the VCR and press Play on = white, and Audio Right = redMono jack of the set Camcorder Other A/V Source SetupEx LCD TV Model Audio 800x600 RGB-PC, HDMI1/DVI-PC modeRGB-PC mode only 640x350 HDMI1/DVI-DTV, HDMI2-DTV mode 59.94Phase Screen Setup for PC mode OverviewInitializing Reset to original factory values Digital Audio Output AV OUT SetupWatching TV / Channel Control Remote Control FunctionsWatching TV / Channel Control Inside the Sliding Cover Installing BatteriesTurning on TV Volume AdjustmentControl Option SetupON-SCREEN Menus Selection Watching TV / Channel Control LockAuto Scan EZ Scan Channel SearchAdd/Delete Channel Manual Scan Small window at the top-left corner of the screen After EZ Scan on the Setup menuChannel Editing There are two different ways in order to add or deleteDTV Signal Strength Press the G button and then use D or Button to Input Source SelectionWatching Select the source T V, AV1, AV2, Component1Input Label SimpLink Preparations SimpLink Menu SimpLink FunctionsBecome imprinted on the screen and remain visible You can also adjust Aspect Ratio in the Option menuPicture Control Set by programPicture 169Horizon ZoomEZ Picture Preset Preset Picture SettingsPicture Control Color Tone PresetEZ Picture User Mode Manual Picture AdjustmentSelect EZ Picture Or G button to Color Tone User ModeSelect X D XD Picture Improvement TechnologyAdvanced Cinema 32 Pull Down Mode Advanced Black Darkness Level Select Video Reset Picture ResetInversion OrbiterLOW Power Picture Mode Plasma TV only Sound & Language Control Preset Sound Settings EZ SoundLanguage Control SoundPress the G button and then use F or G button to Make appropriate adjustmentsBalance Select BalanceSound & Language Control TV Speakers ON/OFF SetupPress Exit button to save and return to TV viewing STEREO/SAP Broadcasts SetupStereo, or SAP appear in turn Them with the SAP buttonAudio Language Select Language ON-SCREEN Menus Language SelectionText Caption / TextAnalog Broadcasting System Captions CaptionSelect Caption/Text Digital Broadcasting System CaptionsOr French Size Set the word size Caption OptionCustomize the DTV/CADTV captions that appear on your screen Sound & LanguageClock Setting Time SettingAuto Clock Setup Time Setting Manual Clock SetupButton and then use Or E button to Auto ON/OFF Timer SettingSleep Timer Setting To select the Time menu Auto SHUT-OFF SettingSelect Auto Off Chip rating and categories SET Password & Lock SystemSetting up Your Password Parental Control / RatingsLock System Set PasswordRating External Input Blocking Channel BlockingParental Control / Rating Movie Rating Mpaa for USA only Movie & TV RatingTV Rating General for USA only TV Rating Children for USA onlyTV Rating English for Canada only Appendix TroubleshootingRemote control Doesn’t work Power is suddenly Turned off AppendixVertical bar or stripe on Background AppendixExtended Absence MaintenanceCleaning the Screen Cleaning the CabinetModels Product Specifications37LC7D 42LC7D Programming a code into a remote mode Programming the Remote ControlVCR Remote Control CodeHdstb Cable BoxDVD AudioIR Codes Remote Control IR CodesCode Function GND RS-232C SetupType of Connector D-Sub 9-Pin Male External Control Through RS-232CCommunication Parameters RS-232C ConfigurationsTransmission / Receiving Protocol Command Reference ListSet ID OK/NGDatax Set ID DataCr Step
Top Page Image Contents