ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied to all of the LED TV with LD34N chassis.
2.Designation
(1)Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument.
(2)Adjustment must be done in the correct order.
(3)The adjustment must be performed in the circumstance of 25 °C ± 5 °C of temperature and 65 % ± 10 % of relative humidity if there is no specific designation.
(4)The input voltage of the receiver must keep AC
(5)The receiver must be operated for about 5 minutes prior to the adjustment when module is in the circumstance of over 15.
In case of keeping module is in the circumstance of 0 °C, it should be placed in the circumstance of above 15 °C for 2 hours.
In case of keeping module is in the circumstance of below
[Caution]
When still image is displayed for a period of 20 minutes or longer (Especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some afterimage in the black level area.
3. Automatic Adjustment
3.1. ADC Adjustment
3.1.1. Overview
ADC adjustment is needed to find the optimum black level and gain in
3.1.2. Equipment & Condition
(1)USB to
(2)
-Resolution : 480i Comp1
1080P Comp1
1920*1080P SCART RGB
-Pattern : Horizontal 100% Color Bar Pattern
-Pattern level : 0.7 ± 0.1
-Image
3.1.3. Adjustment
(1)Adjustment method
-Using
(2)Adj. protocol
Protocol | Command | Set ACK | |
Enter adj. mode | aa 00 00 | a 00 OK00x | |
Source change | xb 00 04 | b 00 OK04x (Adjust 480i, 1080p Comp1 ) | |
xb 00 06 | b 00 OK06x (Adjust 1920*1080 SCART RGB) | ||
| |||
Begin adj. | ad 00 10 |
| |
Return adj. result |
| OKx (Case of Success) | |
| NGx (Case of Fail) | ||
|
| ||
| (main) | (main) | |
Read adj. data | ad 00 20 | 000000000000000000000000007c007b006dx | |
(sub ) | (Sub) | ||
| |||
| ad 00 21 | 000000070000000000000000007c00830077x | |
|
| NG 03 00x (Fail) | |
Confirm adj. | ad 00 99 | NG 03 01x (Fail) | |
NG 03 02x (Fail) | |||
|
| ||
|
| OK 03 03x (Success) | |
End adj. | aa 00 90 | a 00 OK90x |
Ref.) ADC Adj. RS232C Protocol_Ver1.0
(3)Adj. order
-aa 00 00 [Enter ADC adj. mode]
-xb 00 04 [Change input source to Component1 (480i& 1080p)]
-ad 00 10 [Adjust 480i&1080p Comp1]
-xb 00 06 [Change input source to RGB(1024*768)]
-ad 00 10 [Adjust 1920*1080 SCART RGB]
-ad 00 90 End adj.
3.2.MAC address D/L, CI+ key D/L, Widevine key D/L, ESN key D/L, HDCP key D/L,
DTCP key D/L
Connect: PCBA Jig →
▪Com 1,2,3,4 and 115200(Baudrate) Mode check: Online Only
▪Check the test process: DETECT → MAC → CI → Widevine → ESN → HDCP → DTCP
▪Play: START
▪Result: Ready, Test, OK or NG
▪Printer Out (MAC Address Label)
Copyright © | LG Electronics. Inc. All rights reserved. | - 13 - | LGE Internal Use Only |
Only for training and service purposes |
|
| |