Q-See QC40108 user manual PAN/TILT/ZOOM Cameras, Connecting a PTZ Camera, PTZ Control and Setup

Page 26

PAN/TILT/ZOOM CAMERAS

CHAPTER 6

6.1 CONNECTING A PTZ CAMERA

The RS485 connector is used to connect and control PTZ cameras. It uses a single-direction protocol meaning that it can send commands out to the camera(s) but not receive any data back from the unit.

The DVR is set by default for RS485 to be disabled for each channel. Therefore, PTZ settings must be enabled before PTZ cameras can be utilized. This system supports 26 of the most common protocols including Pelco-D and Pelco-P.

When connecting a PTZ camera, the following should be taken into account:

• Ensure that the camera has the same grounding with the DVR otherwise you may not be

able to control the PTZ. Shielded twisted wire is recommended with the shielded layer being

used to connect to the ground. Improper grounding may result in chip damage.

• For excessively long wire runs, or if multiple PTZ cameras are connected to the DVR, 120Ω

should be parallel connected between the A and B lines on the far end to reduce reflection

6.2 PTZ CONTROL AND SETUP

The following instructions are based on the Pelco-D protocol. You will need to have the manual for your PTZ camera at hand to ensure the proper settings within the DVR.

SETUP

For ease of set-up, the PTZ camera’s video feed should be displayed on the screen.

STEP 1. Open the Pan/Tilt/Zoom Menu from the Settings menu. You cannot use the Shortcut Menu to access the PTZ controls until after you have configured a channel to use PTZ.

and maintain the signal quality

• The 485 port of this DVR cannot parallel connect with the 485 port of another device

• The voltage between the A and B lines of the camera should be less than 5V.

STEP 2. Be certain that the channel

PICTURE 6-2

CHAPTER 6

STEP 1. The data cable from the PTZ camera must be connected to the ports highlighted in Picture

6-1. Multiple PTZ cameras can be connected to this port, but you may require an expander port to do so.

STEP 2. Connect the other end of the cable to the proper pins in the connector on the camera

STEP 3. Connect the camera video and power cables as you would any other camera.

RS-485

1 2 3 4 NO C A B Rx Tx

PICTURE 6-1

listed at the top is the one which the PTZ camera will be connected to. Enter data into the other fields according to the data provided in your PTZ camera’s manual, including protocol, data bits, stop bits and parity.

STEP 3. Click the save button once you have entered the settings. If you are operating an identical PTZ camera on another channel, you may use the Copy and Paste buttons to apply those settings to the channel that camera is connected to.

STEP 4. Once you have saved your settings and exited the menu, you can right-click the mouse to bring up the Shortcut Menu allowing you to select the Pan/Tilt/Zoom controls.

PICTURE 6-3

PAN/TILT/ZOOM CAMERAS

PICTURE 6-4

50

51

Image 26
Contents Model QC40108 About this Manual Table of Contents Questions or Comments? Contact Us Troubleshooting Minimum Computer ConfigurationIntroduction Features and Specifications Connection InstallationDVR Installation ConnectionsVideo Output CamerasAudio Input and Output Virtual Keyboard ControlsMouse Control Remote Control Num Name FunctionOperation Basic OperationFront and Side Panels Live ViewMain Menu LOGIN, Logout and Main MenuLogin Shortcut MenuLogout Search and PlaybackRecording Auto ResumeStart, Stop and Play SearchPlayback Video Clip ZoomBack-up MOTION, Video Loss and Camera Masking Detection Basic OperationSchedule Motion DetectionEvent Response Video LossCamera Masking Backup Main Menu MenusMenus Info MenuVersion BPSLOG Online UsersSetting Menu GeneralEncode Detect Network AlarmSchedule PAN/TILT/ZOOMDefault DisplayHDD Manage Alarm OutputAdvanced AbnormalityRecord TV AdjustShutdown AccountSetup Connecting a PTZ CameraPTZ Control and Setup PAN/TILT/ZOOM CamerasControl Setting PRESET/PATROL/PATTERN/SCANPreset PatrolAlarm Input AlarmsAlarm Running PTZ FunctionsAlarm Output Alarm Setup and Activation AlarmsHard Disk Drive INSTALLATION/REMOVALIs covered in .2 Ptzpicture 7-5Control and Setup Hard Disk DriveVideo Resolution Frame BIT Space Format Rate Quality Used Calculating the Recording Capacity of a Hard Disk DriveAppendix TroubleshootingAppendix Minimum Computer Configuration Minimum required configuration of a PC for remote connectionSee Products See Product WarrantyLiability Exclusions
Related manuals
Manual 9 pages 34.35 Kb