Q-See QC40108 user manual Alarms, Alarm Input, Running PTZ Functions

Page 28

RUNNING PTZ FUNCTIONS

Clicking on the Page Switch button in the PTZ Control Panel (Picture 6-5) will switch to a new window (Picture 6-11) which allows you to activate the functions created above as well as the Auto Pan and Flip functions.

Enter the number of the function you wish to activate and select the function button to run that function.

ALARMS

CHAPTER 7

This DVR features connections for external alarms – both input and output. When an event is detected the system can notify local users or send notification to a monitoring service. At the same time, the system can accept signals from motion detectors, smoke detectors or other alarms and begin recording based on that input and your settings.

You will need to have the manual for your alarm(s) handy to ensure the proper settings within the DVR.

In addition, there are other functions that can be engaged in this window.

AutoPan - This will cause the camera to

PICTURE 6-11

automatically rotate.

Flip - Most PTZ cameras have a mechanical stop which will prevent the camera from rotating a full 360°. If the camera is tracking someone or some thing and it reaches this stop, pressing Flip will bring the camera around the other direction to continue tracking. Some PTZ cameras have “E-flip” which will do this automatically.

7.1 ALARM INPUT

When attaching alarms, the following criteria must be met:

1.The alarm input must be grounded.

2.A grounding signal is required for the alarm input

3.When connecting the DVR to another device - including another DVR - through the alarm input, a relay should be used to separate them.

ALARM IN

1 2 3 4 NO C A B Rx Tx

PICTURE 7-1

CHAPTER 7 ALARMS

Page Switch - returns you to the PTZ Control Panel (Picture 6-5)

Reset - This ends the currently running function.

Parameter

Grounding Alarm

 

 

 

 

 

 

 

 

 

 

 

 

 

Ground line

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Alarm Input

1, 2, 3, 4 becomes valid in low voltage.

 

 

 

 

 

 

 

NO C

One NO activation outputs.

 

 

 

 

 

 

 

54

55

Image 28
Contents Model QC40108 About this Manual Table of Contents Introduction Troubleshooting Minimum Computer ConfigurationQuestions or Comments? Contact Us Features and Specifications Installation DVR InstallationConnection ConnectionsAudio Input and Output CamerasVideo Output Mouse Control ControlsVirtual Keyboard Remote Control Num Name FunctionBasic Operation Front and Side PanelsOperation Live ViewLOGIN, Logout and Main Menu LoginMain Menu Shortcut MenuSearch and Playback RecordingLogout Auto ResumePlayback SearchStart, Stop and Play Back-up ZoomVideo Clip Basic Operation ScheduleMOTION, Video Loss and Camera Masking Detection Motion DetectionCamera Masking Video LossEvent Response Backup Menus MenusMain Menu Info MenuBPS LOGVersion Online UsersSetting Menu GeneralEncode Network Alarm ScheduleDetect PAN/TILT/ZOOMDefault DisplayAlarm Output AdvancedHDD Manage AbnormalityTV Adjust ShutdownRecord AccountConnecting a PTZ Camera PTZ Control and SetupSetup PAN/TILT/ZOOM CamerasSetting PRESET/PATROL/PATTERN/SCAN PresetControl PatrolAlarms AlarmAlarm Input Running PTZ FunctionsAlarm Output Alarm Setup and Activation AlarmsINSTALLATION/REMOVAL Is covered in .2 Ptzpicture 7-5Control and SetupHard Disk Drive Hard Disk DriveVideo Resolution Frame BIT Space Format Rate Quality Used Calculating the Recording Capacity of a Hard Disk DriveAppendix TroubleshootingAppendix Minimum Computer Configuration Minimum required configuration of a PC for remote connectionLiability Exclusions See Product WarrantySee Products
Related manuals
Manual 9 pages 34.35 Kb