Q-See QC40198 user manual Navigation and Controls

Page 42

NAVIGATION AND CONTROLS

QC40198 User Manual

 

 

 

 

Event type: from the dropdown list you can select motion detection type.

Channel: select the channel to activate recording function once alarm occurs. Please make sure you have set MD record in encode interface (Main Menu->Setting->Schedule) and schedule record in manual record interface (Main Menu->Advanced->Manual Record)

Latch: when motion detection event ends, system auto delays detecting again for a specified time. The value ranges from 10-300 seconds.

Region: Click select button in the Regionportion of the Detect menu illustrated in Figure 4-20. Here you can set the motion detection zone. As illustrated in Figure 4-21 below, there are 396 (22*18 PAL) /330 (22*15 NTSC) small zones. The green square is current cursor position. The Red zone is the motion detection zone. Black zone is the disarmed zone. You can click the Fn button on the remote to switch between the arm mode and disarm mode. In arm mode, you can click the direction buttons to move the green rectangle to set the motion detection zone. After you completed the setup, please click ENTER button to exit current setup. Click save button to save current setup. If you click ESC button to exit the region setup interface the system will not save your zone setup.

NOTICE: as shown in Figure 4-21, you can left click the mouse and then drag it to set a region for motion detection. Click Fn to switch between arm/withdraw motion detection. After setting, click enter button to exit.

Figure 4-21

Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.

Show message: System can pop up a message to alert you in the local host screen if you enable this function.

Alarm upload: System can upload the alarm signal to the network (including alarm center) if you enable this function.

Send email: System can send out an email to alert you when alarm occurs.

PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go to preset, tour & pattern when there is an alarm. Click selectbutton, you can see the interface shown in Figure 4-22. Please note: motion detection can only activate the preset.

33 P a g e

Image 42
Contents LCD Observation System See Products Contact USSafety Instructions Electrical SafetyWarranty Information Thank You for Choosing a Q-See ProductProduct Registration Customer Information CardTable of Contents Backup Search 118 Features & Specifications FeaturesUser-Friendly LCD Control Functions Included Mouse and Remote ControlAlarm Activation Function Storage FunctionSpecifications System ResourcesChannel Information Motion Detection and Alarm Password Controls Front Panel and Side PanelRear Panel Remote Control Controls Mouse Control Mouse DoubleLeft Click RightInstallation & Connection Connection DiagramWhat’s in the Box Device Installation Hard Drive Installation Connecting Power Supply Connecting Video InputConnecting Video Output Connecting Audio Input & Output, Bidirectional Audio Audio InputAudio Output Alarm Input and Output Connection Alarm inputAlarm output Alarm Input and Output Details How to connect PTZ cameraAlarm Input Port Alarm Output PortModel JRC-27F RS232 RS485Other Interfaces Navigation and Controls Login, Logout & Main MenuLogin Main MenuAuto Resume after Power Failure LogoutBasic Operation Enable/Disable RecordManual Recording Live ViewingEnable all channel recording Stop All Channel RecordingSearch & Playback Search MenuNumber Function Playback Schedule Menu ScheduleCalendar Button Illustration RemarksQuick Setup SnapshotActivate Snapshot Go to Detect Menu Motion DetectionImage FTP Motion DetectNavigation and Controls Navigation and Controls Video Loss Camera MaskingTips Alarm Setup and Alarm Activation Alarm setupNavigation and Controls Backup Detect DeviceBackup Device TipsPTZ Control and Color Setup PTZ SetupCable Connection Navigation and Controls Preset/ Patrol/Pattern/Scan Intelligent Positioning KeyPreset Setup Activate PresetPatrol setup Tour Setup Activate Patrol tour Pattern SetupAuto Scan Setup Activate Pattern FunctionFlip Activate Auto ScanMain Menu Menu TreeSetting Main MenuGeneral Encode Schedule 4 RS232 NetworkMain Menu Advanced Network Setup IP FilterPPPoE NTP Setup City /Region NameDdns Setup DNSFTP Main Menu Alarm Detect8 Pan/Tilt/Zoom DisplayMain Menu Default Search AdvancedHDD Management Alarm Output AbnormityAccount TV Adjust InformationAuto Maintain HDD Information 2 BPS3 Log VersionShutdown Online UsersAuxiliary Menu Go to Pan/Tilt/Zoom MenuPreset /Patrol / Pattern /Border Function Intelligent Positioning KeyPatrol Setup Activate PatrolBorder Setup Activate Border FunctionFlip WEB Operation Network ConnectionPop-Ups and ActiveX Controls WEB Operation Login WEB Operation Real-time Monitoring Start Dialogue Open AllRefresh Local PlayZoom/Focus/Iris Direction key and 3D positioning keySpeed 2 PTZPattern PresetAuto Scan Auto tourColor Picture Path and Record PathWEB Operation HDD information ConfigureVersion Information System InformationLog General Setup System ConfigurationPlease click save button to save your current setup DST Encode  One channel supports up to 4 privacy mask zones Schedule Whole week RS232 System default setup is NetworkA g e WEB Operation NAS NTP Alarm Please refer to the following chart for detailed information Motion Detection PTZWEB Operation WEB Operation PTZ Default & Backup Advanced HDD Management Alarm I/O Here you can search alarm output status. See FigureRecord Auto Maintenance AccountSnapshot Abnormity Additional Function WEB Operation WEB Operation Alarm WEB Operation Un-install Web Control AboutLog out Setup MYQ-SEE Ddns MY Q-SEE DdnsMY Q-SEE Ddns MY Q-SEE Ddns Smartphone Access Smartphone AccessSymbian LCD does not work after device boots up. Possible causes TroubleshootingCombo DVR does not boot up properly. Possible causes System cannot detect hard drive. Possible causesCannot search local records There is no audio when monitoringReal-time video color is distorted. Possible causes Time display is not correct. Possible causesCannot log in client-end or web. Possible causes Combo DVR cannot control PTZ. Possible causesMotion detection function does not work. Possible causes Network connection is not stable. Possible causesAlarm function is not working. Possible causes Burn error /USB backup error. Possible causesAlarm signal cannot be disarmed. Possible causes Remote control does not work. Possible causesDaily Maintenance Appendix a Appendix a HDD Capacity CalculationAppendix B Appendix B Compatible USB Drive ListAppendix C Appendix C Compatible CD/DVD Burner ListAppendix D Appendix D Compatible Sata HDD ListWD1600AABS2
Related manuals
Manual 8 pages 36.54 Kb

QC40198 specifications

The Q-See QC40198 is a high-performance surveillance camera designed to provide comprehensive security solutions for residential and commercial properties. This camera is a part of Q-See's extensive range of security products known for their durability, advanced technology, and user-friendly interface.

One of the main features of the QC40198 is its high resolution. Equipped with a 4MP sensor, this camera delivers crisp and clear images, allowing you to capture fine details even from a distance. This enhanced resolution ensures that you can identify faces, license plates, and other important details, contributing to an effective security system.

The QC40198 also boasts advanced night vision capabilities, utilizing infrared technology to provide clear images in low-light conditions. With a range of up to 100 feet, you can rely on this camera to monitor your property during the night, offering peace of mind even after dark. The automatic switching feature ensures that the camera seamlessly transitions between day and night modes, maintaining optimal visibility at all times.

In terms of durability, the QC40198 is built to withstand various weather conditions, making it suitable for outdoor installations. It features an IP66 weatherproof rating, which means it is resistant to dust and can endure heavy rain, ensuring continued functionality year-round. This robustness makes it a reliable choice for safeguarding your home or business.

The camera also incorporates advanced motion detection technology. This feature helps reduce false alarms by allowing you to set specific parameters for motion detection, ensuring that you are only alerted when necessary. Coupled with real-time alerts sent directly to your smartphone or tablet, you can monitor your property remotely and respond to potential threats promptly.

Another significant characteristic of the Q-See QC40198 is its compatibility with various smart home ecosystems. It can be easily integrated with other smart devices, providing you with the flexibility to expand and customize your security network as needed.

In conclusion, the Q-See QC40198 is a reliable and feature-rich surveillance camera ideal for those seeking an effective security solution. With its high resolution, night vision capabilities, durability, advanced motion detection, and seamless integration with smart home systems, this camera stands out as a top choice in the ever-evolving landscape of security technology. Whether for home or business use, the Q-See QC40198 delivers comprehensive surveillance to enhance safety and security.