SRS Labs WL66 owner manual Safety Precautions, Air Circulation, Heat Damage, Mains Supply, Do not

Page 3

Safety Precautions

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken to obtain the best results and for safety to be assured. Please read the points below for your own safety. They are of a general nature, intended to help with all electronic consumer products and some points may not apply to the goods you have just purchased.

English

Air Circulation

Leave at least 10cm clearance around the television to allow adequate ventilation. This will prevent overheating and possible damage to the television. Dusty places should also be avoided.

Heat Damage

Damage may occur if the television is left in direct sunlight or near a heater. Avoid places subject to extremely high temperatures or humidity. Place in a location where the temperature remains between 5°C (41°F) min. and 35°C (94°F) max.

Mains Supply

The mains supply required for this equipment is 220-240v AC 50/60Hz. Never connect to a DC supply or any other power source. DO ensure that the television is not standing on the mains lead. DO NOT cut off the mains plug from this equipment, this incorporates a special Radio Interference Filter, the removal of which will impair its performance.

IF IN DOUBT PLEASE CONSULT A COMPETENT ELECTRICIAN.

Do

DO read the operating instructions before you attempt to use the equipment.

DO ensure that all electrical connections (including the mains plug, extension leads and inter-connections between pieces of equipment) are properly made and in accordance with the manufacturers’ instructions. Switch off and withdraw the mains plug before making or changing connections.

DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

DO be careful with glass panels or doors on equipment.

DO NOT REMOVE ANY FIXED COVERS AS THIS WILL EXPOSE DANGEROUS AND 'LIVE' PARTS.

THE MAINS PLUG IS USED AS A DISCONNECTING DEVICE AND THEREFORE SHOULD BE READILY OPERABLE.

Do not

DO NOT obstruct the ventilation openings of the equipment with items such as newspapers, tablecloths, curtains, etc. Overheating will cause damage and shorten the life of the equipment.

DO NOT allow electrical equipment to be exposed to dripping or splashing or objects filled with liquids, such as vases, to be placed on the equipment.

DO NOT place hot objects or naked flame sources, such as lighted candles or nightlights on, or close to equipment. High temperatures can melt plastic and lead to fires.

DO NOT use makeshift stands and NEVER fix legs with wood screws. To ensure complete safety, always fit the manufacturers’ approved stand, bracket or legs with the fixings provided according to the instructions.

DO NOT listen to headphones at high volume, as such use can permanently damage your hearing.

DO NOT leave equipment switched on when it is unattended, unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off by withdrawing the plug, make sure your family know how to do this. Special arrangements may need to be made for people with disabilities.

DO NOT continue to operate the equipment if you are in any doubt about it working normally, or it is damaged in any way – switch off, withdraw the mains plug and consult your dealer.

ABOVE ALL NEVER let anyone, especially children, push or hit the screen, push anything into holes, slots or any other openings in the case.

NEVER guess or take chances with electrical equipment of any kind – it is better to be safe than sorry.

3

Image 3 Contents
Toshiba Contents Mains Supply Safety PrecautionsAir Circulation Heat DamageSide View Installation and important informationWhere to install Please take noteInserting batteries and effective range of the remote Remote controlUPConnecting external equipment Aerial cablesScart leads Please Note Connecting a computerSignal information for Mini D-sub 15 pin connector Signal name Pin NoSwitching on Using the controls and connectionsControls and input connections Auto tuning Manual tuningSelect your language Manual tune SET UPHDMI2 HDMI1 B3C B2 DVD Manual settingManual tune Programme skip Programme skipSound controls Using Auto tuningAuto tune, general controls, sound controls Selecting programme positionsDual Sound controls , SRS WOW sound Effects, dual, stable soundBass boost SRS WOW sound effectsSuper Live Widescreen viewingExact Scan Wide Super Live Cinema Subtitle 149 149Picture position Picture controlsPicture position Back lightMpeg NR Noise Reduction Select Picture settings from the Picture menuPicture preferences Black stretch3D Colour management Colour temperatureBase colour adjustment Base colour adjustmentBlue screen Cinema modeSide panel adjustment Automatic format WidescreenTime Display TimerTimer Panel lockSampling clock Clock phaseReset PC SettingsPress Bto select B1, B2, B3C EXT1-3,HDMI1, HDMI2 or PC Input signal selectionInput selection AV connections Input selectionHDMI1audio If the sound is missing select an alternative settingInput selection and AV connections PC audioText information Navigating pages using AutoNavigating pages using List Selecting modesFor use with P fand P eto view sub-pages when available Text services Control buttonsCheck that Panel lock is not on Sampling clock and adjust until the lines clearCorrect input by pressing B Check all lead connectionsCheck the Speaker option in the Sound menu is set to Off Clock phase and adjust until the picture clearsSpecifications and accessories