IBM LC-UXT3 manual Appendix, Operating Wireless Mouse, Maintenance, Installation

Page 43

APPENDIX

OPERATING WIRELESS MOUSE

Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most Personal Computers. POINT buttons and two CLICK buttons are used for wireless mouse operation.

This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ON- SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse function cannot be used.

INSTALLATION

To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied) is required. Make sure that mouse driver is properly installed in your computer. And make sure that mouse port (or USB port) of a Personal Computer is activated.

1

Connect mouse port (or USB port) of your computer to Control

Port (or USB connector) of this projector with Control Cable (or

 

USB cable). (Refer to page 13, 14 for connection.)

2

Turn a projector on first, and then turn on your computer. When

computer is switched on first, Wireless Mouse may not work

properly.

Note : When your computer has no mouse port, connect Serial Port of your computer to Control Port of a projector with Control Cable for Serial Port (not supplied).

OPERATING WIRELESS MOUSE

When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK button on Wireless Remote Control Unit.

POINT button

POINT button (Move pointer)

Used to move PC mouse pointer. Pointer is moved corresponding with direction you are pressing.

SELECT (LEFT CLICK) button

This button has same function as left button in a PC mouse.

RIGHT CLICK button

This button has same function as right button in a PC mouse. This button is not available for controlling this projector.

SELECT button

RIGHT CLICK button

(left button of mouse)

(right button of mouse)

MAINTENANCE

WARNING TEMP. INDICATOR

WARNING TEMP. Indicator flashes red and projector is automatically turned off when an internal temperature of a projector exceeds normal temperature. Wait at least 5 minutes before turning on projector again.

When WARNING TEMP. Indicator continues to flash, check items listed below.

1

Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are

not obstructed.

2

Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING

on next page.

3

If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be

malfunctioning. Contact service personnel from an authorized dealer or a service station.

43

Image 43
Contents Multimedia Projector Model LC-UXT3Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationConnecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Lens Shift Adjustment Preparation Lens InstallationPositioning Projector Moving Projector Preparation Picture Level and Tilt AdjustmentReplacement of Terminal Connecting ProjectorTerminals of Projector AV Input VIDEO/Y, C Jacks Connecting Projector INPUT/OUTPUT Terminals and Jacks InputBNC Input Jacks Audio Input JacksJack Reset ButtonSerial Port Terminal Serial Port OUT TerminalTerminals Projector Connecting to ComputerTerminals Connecting to Video EquipmentBefore Operation Side Controls and IndicatorsSide Controls Lamp Replace Indicator IndicatorsReady Indicator Lamp IndicatorLaser Pointer Function Operation of Remote ControlFocus Button Volume ButtonWired Remote Jack Zoom ButtonOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Turning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorKeystone Adjustment Adjusting ScreenZoom Adjustment Focus AdjustmentBasic Operation Picture Freeze Function Timer FunctionNo Show Function Sound Menu Sound AdjustmentDirect Operation Menu OperationInput Computer InputSelecting Input Source Selecting Computer SystemPC System Menu Computer Input Automatic MULTI-SCAN SystemSelect Computer System Manually AutoResolution Computer Input Compatible Computer SpecificationsComputer Input PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area H Display areaFull screen Image 1~4 Picture Image AdjustmentImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input When Select Input 2 5 BNC TerminalPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N Component Video Signal FormatSelecting Video System Video InputCinema Progressive scan Video Input Image Level AdjustmentColor TintProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Projector To change code of Remote Control UnitUSB Wireless Mouse modeProjector mode Lamp counter resetOperating Wireless Mouse Operating Wireless MouseMaintenance InstallationCleaning Projection Lens Appendix AIR Filter Care and CleaningYellow Lamp Dim Lamp Red Lamp Mark on Lamp Appendix Lamp ManagementFront Indicators Rear Indicators Appendix Lamp ReplacementLamp Handling Precautions Troubleshooting Function does not Remote Control UnitWireless Mouse Does not workTechnical Specifications DVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsSerial Port IN/OUT Terminal Appendix Appendix Appendix Key to better communications Canada