Sylvania 6313CD, 6319CD Channel SET UP Again, Deleting or Adding Channel, Automatic Clock Setting

AUTOMATIC CLOCK SETTING

Make sure ...

• The TV/VCR is turned on.

• Confirm the TV/VCR is receiving a RF (Radio

4Enter the channel number that contains the Automatic Clock Setting Signal

Frequency) signal from either an antenna or cable

system connection using the ANT IN jack on the

rear of the TV/VCR.

NOTE:

•If a cable converter box is being used, make sure it is powered on.

•You must use the TV/VCR remote control to per- form the clock setting procedure.

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L button to select “SETTING CLOCK”.

Press the F.FWD/B button to enter “SETTING CLOCK” menu. Press the STOP/L button to select “AUTO CLOCK CH”.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL

BSETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

– SETTING CLOCK –

AUTO CLOCK	[ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH	[ 45]
MANUAL CLOCK SET

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL

Press the F.FWD/B or REW/s buttons until you locate Auto Clock Set station number. See item 3 above.

D.S.T. [OFF]

Press the PLAY/K or STOP/L but-

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to enter

“SETTING CLOCK” menu.

BSETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

Press the MENU button to exit the screen.

5Turn off the TV/VCR

Once the TV/VCR is turned off , it will periodically check and set the correct date and time.

2 Set “AUTO CLOCK” to [ON]	– SETTING CLOCK –
Press the F.FWD/B button until	B AUTO CLOCK	[ON]
AUTO CLOCK [ON] appears.	AUTO CLOCK CH SEARCH
	MANUAL CLOCK SET	[ 02 ]
	AUTO CLOCK CH
	D.S.T.	[OFF]

CHANNEL SET UP AGAIN

Make sure ...

•Press the POWER button to turn on the TV/VCR.

3Begin “AUTO CLOCK CH SEARCH”

Press the STOP/L button to select “AUTO CLOCK CH SEARCH”.

Press the F.FWD/B button.

– SETTING CLOCK –

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK

B CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

• The TV/VCR is now searching

for the station which contain the

auto clock set signal. The search

for a signal may take up to 20

AUTO CLOCK [ON]

BAUTO CLOCK CH SEARCH

AUTO CLOCK CH	[ 02 ]
MANUAL CLOCK SET
D.S.T.	[OFF]

UP”.

Then, press the F.FWD/B button.

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

seconds per channel.

•“_ _” appears at the lower left of

the screen when the search has

ended.

• Auto Clock station- write down

the number(s) that appear on the

screen. These are the auto clock

station(s) in your area. See item

– AUTO CLOCK CH SEARCH –

08 10 13

_ _

2Begin auto preset

Press the PLAY/K or STOP/L but- ton to point to “AUTO PRESET”. Then, press the F.FWD/B button. The tuner scans and memorizes all the active channels in your area.

– CHANNEL SET UP –

ADD / DELETE CH (TV)

BAUTO PRESET

4 below.

3After scanning

•If no number(s) appear on the TV screen, there are no stations in your area which contain the Auto Clock signal. Auto Clock Setting is not possible. Please use Manual Clock Setting on page 11.

Press the MENU button to exit the screen. NOTE: During Auto Clock CH Search, the picture may be distorted. This is normal.

The tuner stops on the lowest memorized channel.

DELETING (OR ADDING)

CHANNEL

The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)

- 12 - EN

9I03