Sylvania 6720FDF DAYLIGHT-SAVING Time, Automatic Clock Setting, To Cancel the DAYLIGHT-SAVING

AUTOMATIC CLOCK SETTING

Make sure ...

•The unit must be turned on.

•Confirm the unit is receiving a RF (Radio Frequency) signal from either an antenna or cable system connection using the ANT. jack on the rear of the unit.

NOTES:

•If a cable converter box is being used, make sure it is powered on.

•You must use the remote control to perform the clock setting procedure.

•If the unit is connected directly to a cable converter box or satellite box, the local PBS station must be selected on the cable box itself and the unit must be set to the output channel of the cable converter box or satellite box (usually channel 3 or 4), to be able to set up or correct the clock automatically.

4Enter the channel number that contains the Automatic Clock Setting Signal

Hit [RETURN] to go back to	– SETTING CLOCK –
“SETTING CLOCK” menu.	AUTO CLOCK	[ON]
Hit [L] to select “AUTO CLOCK	AUTO CLOCK CH SEARCH
	B AUTO CLOCK CH	[ 45]
CH”.	MANUAL CLOCK SET
	D.S.T.	[OFF]

Press [s / B] until you locate Auto

Clock Set station number.

5Exit the setting clock mode

Hit [SETUP] to exit the menu.

NOTE:

•Once the unit is turned off, it will periodically check and set the correct date and time.

1Select “SETTING CLOCK”

Hit [SETUP].

Press [K / L] to select “SETTING CLOCK”, then hit [ENTER] .

- TV/VCR SETUP -

TIMER PROGRAMMING

BSETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH INDEX SEARCH

DAYLIGHT-SAVING TIME

TV/VCR

Select this feature and the unit’s clock automatically will advance one hour in April, then reverse one hour in October.

When Daylight-Saving Time is ON, the clock will change automatically as follows:

	2 Set “AUTO CLOCK” to [ON]	– SETTING CLOCK –		• First Sunday of April : At 2 AM the clock immedi-
Hit [ENTER] to select [ON].		B AUTO CLOCK	[ON]	ately changes to 3 AM. Any timer programming
		AUTO CLOCK CH SEARCH		you have set to occur between 2 AM and 3 AM will
		AUTO CLOCK CH	[ 02 ]	not record.
		MANUAL CLOCK SET
				• Last Sunday of October : At 2 AM the clock
		D.S.T.	[OFF]
				immediately changes to 1 AM.
				Make sure ...
	3 Begin “AUTO CLOCK CH SEARCH”
				• The unit must be turned on.
Hit [L] to select “AUTO CLOCK
		– SETTING CLOCK –
CH SEARCH”.		AUTO CLOCK	[ON]
				1 Select “SETTING CLOCK”
Then hit [ENTER].		B AUTO CLOCK CH SEARCH			- TV/VCR SETUP -
					TIMER PROGRAMMING
•	The unit begins searching for the	AUTO CLOCK CH	[ 02 ]	Hit [SETUP].
					B SETTING CLOCK
		MANUAL CLOCK SET			CHANNEL SET UP
	station which contains the auto			Press [K / L] to point to “SET-	USER’S SET UP
		D.S.T.	[OFF]		V-CHIP SET UP
					LANGUAGE [ENGLISH]
	clock set signal. The search for a			TING CLOCK”, then hit [ENTER].	CAPTION [OFF]
					ZERO RETURN
					TIME SEARCH

signal may take up to 20 seconds per channel. INDEX SEARCH

•When the search has ended, “_ _” – AUTO CLOCK CH SEARCH –

appears at the lower left of the	08 10 13		2 Set “D.S.T.” (Daylight-Saving Time) to [ON]
screen.
			Press [K / L] to point to “D.S.T.”,
• Write down the number(s) that				– SETTING CLOCK –
			then hit [ENTER] until [ON]	AUTO CLOCK	[ON]
appear on the screen. They are the
	_ _		appears.	AUTO CLOCK CH SEARCH
auto clock station(s) in your area.				AUTO CLOCK CH	[ 02 ]
• If no number(s) appear on the TV screen, there are				MANUAL CLOCK SET
				B D.S.T.	[ON]
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 18.			3 Exit the Daylight-Saving Time mode
NOTE:			Hit [SETUP] to exit the menu.
			TO CANCEL THE DAYLIGHT-SAVING
• During AUTO CLOCK CH SEARCH, the picture
			TIME
may be distorted.
			Repeat steps 1 to 2 and select [OFF] using
			[ENTER].
		- 19 -			EN