Magnavox CC13C1MG, CC19C1MG owner manual To change the access code, follow these steps

Page 44

44 SmartLock (cont’d)

To change the access code, follow these steps.

1

Press the MENU button.

6 2,4

> SMARTLOCK			PRESS B
	REVIEW
	EXIT
	PRIM. SETUP
	VCR PROGRAM
	VCR SETUP

2

Press the PLAY/▲ button or the STOP/▼ button to select SMARTLOCK. Then, press the F.FWD/B button.

SMARTLOCK

__ _ _

1

5

3

EJECT

MENU

1

4

7

SLEEP/

WAKE UP

REC

/OTR

POWER

STATUS/EXIT CLEAR

2 3

5 6

8 9

ALT.CH

0

PAUSE

/STILL

PLAY

Enter Your Access Code

3

Use the Number buttons to enter your old access code. The default code is 0711. If you have never set up your personal access code, use 0711 now.

After you enter the code, the SMARTLOCK menu will appear.

SMARTLOCK

X X X-

Enter Your Access Code

4

Press the PLAY/▲ button or the STOP/▼ button to select CHANGE CODE. Then, press the F.FWD/B button.

SMARTLOCK

BLOCK

>CHANGE CODE

SELECT KL CHOOSE B

TO END PRESS EXIT

5

Use the Number buttons to enter your desired access code in the New Code space. Then, enter the same code in the Confirm Code space.

Your new access code should be recorded. You will return to the SMARTLOCK menu.

New Code		_	_ _ _


Confirm Code	_		_ _ _

6

Press the STATUS/EXIT button.

REW F.FWD

STOP

CH.VOL.

MUTE

SPEED

TRACKING MEMORY

Helpful Hints

•To protect the privacy of the access code, an X will appear on the screen instead of the number you enter.

•If a “Wrong Code...” message appears on the screen after you com- plete step 5, you entered the wrong numbers in the Confirm Code space. Repeat the steps on this page.

•You cannot use the default code after you set up your personal access code.

•If a power failure occurs, the default code, 0711, will be the active access code again.

•If you connect the power cord to an AC outlet that is controlled by a wall switch, your personal access code will be erased every time you turn off the power at the wall switch. The default code will be the active code again.

Image 44

Contents Tvcr Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Battery Safety Using the Remote ControlTV/VCR Maintenance Replace the battery compartment lidHook up your TV/VCR using one of the connections shown Hooking Up the TV/VCRRF coaxial cable Not supplied Rod AntennaHooking Up the TV/VCR cont’d Bent pinCrooked Pin Straight Pin Cable PlugTurning On the TV/VCR Press the Menu button. The screen shown below will appearSelect Language English Español Select KL To END Press Exit Language SelectionPress the Menu button Automatic Channel Setup Wait for the TV/VCR to set up channelsAdding/Deleting Channels Press the PLAY/o button or the STOP/p button to selectRepeat steps 3-4 to add or delete other channels Programming of the channel you added or deleted will appearCable Box users must set the clock manually Setting the ClockManual Clock Setting SET Manual Clock Time Date To END Press Exit SET Manual Clock TimeMonth To Correct Press Clear To END Press Exit Date Sunday To Correct Press Clear To END Press ExitSetting the Clock cont’d PRIM. Setup Press BVCR Program VCR Setup Caption Reminder Brightness Automatic PBS Channel SelectionNOW Searching flashes on the TV/VCR screen Wait for the TV/VCR to find the timeSET Auto Clock Time Date NOW Searching To END Press Exit SET Auto Clock TimeManual PBS Channel Selection Use the Number buttons to select your PBS station PRIM. SETUP. Then, press the F.FWD/B button PRIM. Setup Press B VCR Program VCR SetupDaylight-Savings Time Press the PLAY/ button or the STOP/ button to selectPrimary Setup Volume BAR SET Clock Select KL Choose B To END Press ExitTime Zone Press the Menu button, then press the STATUS/EXIT buttonFront Panel AC Power Cord Rear PanelANTenna Jack Connect your antenna or cable here. Details are on page sixRemote Control Buttons Menu Button STATUS/EXIT ButtonREWind/ Button STOP/ ButtonAdjusting the Picture Controls When you finish, press the STATUS/EXIT buttonAdjusting the Picture Controls cont’d Tint KK Sharpness TV ResetDecrease Increase Decreased brightnessOn-Screen Status Displays If you select Status ON, then select Counter only OFFIf you select Status ON, then select Counter only on If you select Status OFFReminder OFFInsert a tape in the TV/VCR PlayingFollow the steps below to play a tape Recording Read and follow the steps below to record a TV programTo stop recording, press the STOP/ button Tape Speeds HrsLength Press OTR Cancel Press Clear One-Touch RecordingTape is in the TV/VCR. The record tab must be intact Press the STOP/EJECT but- ton on the TV/VCR to stop the OTRTV/VCR is now in Line Input mode Rerecording Tape DuplicationSelect Program Number To END Press Exit Timer RecordingDaily ONE Time Program Channel Time on Time OFF To Correct Press Clear To END Press ExitTimer Recording cont’d Timer recording information for the program in the lowest With the TV/VCR on, press the Menu buttonProgram REVIEW, then press the F.FWD/B button Gram Review and press the F.FWD/B buttonVCR Setup ONE Time Play Defeat RecordingFollow the steps below to prevent accidental recording REC DefeatedVCR SETUP, then press the F.FWD/B button VCR Setup ONE Time Play Repeat Play onRepeat Play TV programming will appear while the tape is rewindingInsert a tape in the TV/VCR Press the Menu button VCR Setup ONE Time Play Repeat Play A-BB Repeat Play Repeat Play cont’d RepeatStop Real-Time Counter MemoryAppear on the screen Viewing a Still Picture Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Smartlock menu will appear SmartLockTo block ratings, follow the steps below Example Specific Sub-ratings SmartLock cont’dRatings are defined on To change the access code, follow these steps After you enter the code, the Smartlock menu will appearBlocked Ratings TV-Y7 TV-GVCR Program VCR Setup Caption Reminder Blue BackgroundPress the SLEEP/WAKE UP button Sleep TimerTimer during a recording Timer Sleep Wake UP Wake Up TimerTimer Sleep Wake UP TV on ON-TIME Volume Bar VCR Program VCR Setup CaptionTo Adjust Press / B Caption Closed CaptionExample Menu ScreenHalf-screen text Closed Caption cont’dStandard Closed Captions Automatic Operation Features Glossary Helpful Hints Helpful Hints cont’d Specifications Model # Serial # Limited WarrantyPlease contact Philips at French Speaking English Speaking Index Page Supplied Accessories