Magnavox CC19C1MG, CC13C1MG owner manual ONE Time Program Channel Time on

Page 33

Timer Recording (cont’d) 33

4

Use the Number buttons (1-8) to select a position in which to store the timer recording. Flashing numbers indi- cate an open position (one in which a timer recording has not been stored yet).

NOTE: If you select a number that already has been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen for a few seconds. Then information about the program in that position will appear on the screen. If this happens, press the STATUS/EXIT but- ton. Then use the Number buttons to select another position.

5

Use the Number buttons to enter the channel of the TV program you want to record.

●If you are recording from line input, press 0, 0. A/V IN will appear on the screen.

●If you are recording using a Cable Box, enter the Cable Box output channel (03 or 04). Be sure to select the channel of the TV program at the Cable Box and leave the Cable Box on for the timer recording.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL – – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

6

Press two Number buttons for the hour(s) you want the recording to begin. Press two Number buttons for the minute(s) you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL

10

TIME ON

– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

7

Follow the instructions in step 6 to set the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM 1

CHANNEL

10

TIME ON

09:30 PM

TIME OFF

– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

Instructions continue on page 34.

4-7

EJECT

POWER

MENU STATUS/EXIT CLEAR

1 2 3

4 5 6

7 8 9

SLEEP/

ALT.CH

WAKE UP

 

0

REC

PAUSE

/OTR

/STILL

PLAY

REW F.FWD

STOP

CH.VOL.

MUTE

SPEED

TRACKING MEMORY

Helpful Hints

•If you enter numbers that do not match the TV/VCR’s clock or calen- dar, the entry will be rejected and a question mark will appear on the screen.

•To make corrections while you are programming a timer recording, press the CLEAR button until the cursor is flashing on the item you want to change. Then enter the cor- rect information.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents
Tvcr For Customer Use Warranty VerificationSafety Precautions FeaturesIntroduction Declaration of ConformityTable of Contents Using the Remote Control Battery SafetyTV/VCR Maintenance Replace the battery compartment lidHooking Up the TV/VCR Hook up your TV/VCR using one of the connections shownRF coaxial cable Not supplied Rod AntennaBent pin Hooking Up the TV/VCR cont’dCrooked Pin Straight Pin Cable PlugPress the Menu button. The screen shown below will appear Turning On the TV/VCRLanguage Selection Press the Menu buttonSelect Language English Español Select KL To END Press Exit Wait for the TV/VCR to set up channels Automatic Channel SetupPress the PLAY/o button or the STOP/p button to select Adding/Deleting ChannelsRepeat steps 3-4 to add or delete other channels Programming of the channel you added or deleted will appearSetting the Clock Manual Clock SettingCable Box users must set the clock manually SET Manual Clock Time SET Manual Clock Time Date To END Press ExitMonth To Correct Press Clear To END Press Exit Date Sunday To Correct Press Clear To END Press ExitPRIM. Setup Press B Setting the Clock cont’dVCR Program VCR Setup Caption Reminder Brightness Automatic PBS Channel SelectionWait for the TV/VCR to find the time NOW Searching flashes on the TV/VCR screenSET Auto Clock Time Date NOW Searching To END Press Exit SET Auto Clock TimeManual PBS Channel Selection Use the Number buttons to select your PBS station PRIM. Setup Press B VCR Program VCR Setup PRIM. SETUP. Then, press the F.FWD/B buttonDaylight-Savings Time Press the PLAY/ button or the STOP/ button to selectVolume BAR SET Clock Select KL Choose B To END Press Exit Primary SetupTime Zone Press the Menu button, then press the STATUS/EXIT buttonFront Panel Rear Panel AC Power CordANTenna Jack Connect your antenna or cable here. Details are on page sixRemote Control Buttons STATUS/EXIT Button Menu ButtonREWind/ Button STOP/ ButtonWhen you finish, press the STATUS/EXIT button Adjusting the Picture ControlsTint KK Sharpness TV Reset Adjusting the Picture Controls cont’dDecrease Increase Decreased brightnessIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status OFFOFF ReminderPlaying Follow the steps below to play a tapeInsert a tape in the TV/VCR Read and follow the steps below to record a TV program RecordingTo stop recording, press the STOP/ button Tape Speeds HrsOne-Touch Recording Length Press OTR Cancel Press ClearTape is in the TV/VCR. The record tab must be intact Press the STOP/EJECT but- ton on the TV/VCR to stop the OTRRerecording Tape Duplication TV/VCR is now in Line Input modeTimer Recording DailySelect Program Number To END Press Exit Time OFF To Correct Press Clear To END Press Exit ONE Time Program Channel Time onTimer Recording cont’d With the TV/VCR on, press the Menu button Timer recording information for the program in the lowestProgram REVIEW, then press the F.FWD/B button Gram Review and press the F.FWD/B buttonDefeat Recording VCR Setup ONE Time PlayFollow the steps below to prevent accidental recording REC DefeatedVCR Setup ONE Time Play Repeat Play on VCR SETUP, then press the F.FWD/B buttonRepeat Play TV programming will appear while the tape is rewindingVCR Setup ONE Time Play Repeat Play A-B B Repeat PlayInsert a tape in the TV/VCR Press the Menu button Repeat Repeat Play cont’dReal-Time Counter Memory Appear on the screenStop Forward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPViewing a Still Picture SmartLock To block ratings, follow the steps belowSmartlock menu will appear SmartLock cont’d Ratings are defined onExample Specific Sub-ratings After you enter the code, the Smartlock menu will appear To change the access code, follow these stepsTV-Y7 TV-G Blocked RatingsBlue Background VCR Program VCR Setup Caption ReminderSleep Timer Timer during a recordingPress the SLEEP/WAKE UP button Wake Up Timer Timer Sleep Wake UP TV on ON-TIMETimer Sleep Wake UP VCR Program VCR Setup Caption Volume BarClosed Caption To Adjust Press / B CaptionExample Menu ScreenClosed Caption cont’d Standard Closed CaptionsHalf-screen text Automatic Operation Features Glossary Helpful Hints Helpful Hints cont’d Specifications Limited Warranty Please contact Philips at French Speaking English SpeakingModel # Serial # Index Page Supplied Accessories