Magnavox CC19C1MG, CC13C1MG owner manual Helpful Hints cont’d

Page 55

Helpful Hints (cont’d) 55

The remote control is not available, or the remote control will not access the menu.

•Use the buttons on the front of the TV/VCR to access the menu. You can not enter numbers (for example, to program a timer recording) using the front panel buttons. Details are on page 20.

TV/VCR has no power.

• Connect the power plug to an AC (alternating current) outlet completely.

TV/VCR power shuts off after 15 minutes.

•To save energy, the TV/VCR will shut itself off after 15 minutes when it is on a channel that is not receiving a broadcast signal (for example, a station that has gone off the air for the night). This is normal.

TV/VCR does not have a picture.

•Adjust the antenna. Details are on page six.

•Adjust the TV/VCR picture controls. Details are on pages 24-25.

•Select an active channel.

TV/VCR has poor sound or no sound.

•Adjust the volume.

•Press the MUTE button to restore the volume.

Tape playback is poor or tape is destroyed.

•Adjust the tracking. Details are on page 52.

•If moisture has accumulated in your TV/VCR, keep the power on for at least two hours, but do not try to play a tape. Details are on page 54.

TV/VCR does not display closed captions.

•Make sure COUNTER ONLY is OFF. Details are on page 26.

•Make sure closed captioning is available for the program. Refer to the TV listings in your local newspaper.

Remote control does not operate TV/VCR.

•Aim the remote control directly at the TV/VCR’s remote sensor. Details are on pages five and 20.

•Remove all obstacles between the remote control and the TV/VCR.

•Inspect and replace the batteries in the remote control. Details are on page five.

Number buttons will not select channels above 69.

•Enter channel numbers as a two-digit number. If you want to select channels 100 and above, enter channel numbers as a three-digit number. Details are on page 22.

•If you are using an antenna, only channels 2-69 will be available. Details are on pages 10-11.

You can not insert a tape into the TV/VCR.

•Insert the tape window side up, with the record tab facing you.

•Make sure a tape isn’t already in the TV/VCR by pressing the STOP/EJECT button on the TV/VCR.

•Gently push on the center of the tape. Never force a tape into the TV/VCR.

•If you have set a timer recording and the TV/VCR power is off, the TV/VCR will eject the tape if the record tab is missing.

You can not remove the tape from the TV/VCR.

•Make sure the power plug is completely connected to an AC (alternating current) outlet.

•If a timer recording is programmed, turn on the TV/VCR power, then eject the tape. Be sure to insert a tape and turn off the TV/VCR power for the timer recording.

TV/VCR ejects the tape when you try to start a recording.

• Make sure the tape has a record tab. Details are on page five.

The cylinder rotates when tape playback is stopped.

•To enable the quick play mechanism, the cylinder will rotate for about five minutes. This is normal. The quick play mechanism switches the tape mechanism from Stop to Play in just one second.

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Tvcr For Customer Use Warranty VerificationDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents Replace the battery compartment lid Battery SafetyUsing the Remote Control TV/VCR MaintenanceRod Antenna Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR RF coaxial cable Not suppliedCable Plug Hooking Up the TV/VCR cont’dBent pin Crooked Pin Straight PinPress the Menu button. The screen shown below will appear Turning On the TV/VCRPress the Menu button Language SelectionSelect Language English Español Select KL To END Press Exit Wait for the TV/VCR to set up channels Automatic Channel SetupProgramming of the channel you added or deleted will appear Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Repeat steps 3-4 to add or delete other channelsManual Clock Setting Setting the ClockCable Box users must set the clock manually Date Sunday To Correct Press Clear To END Press Exit SET Manual Clock Time Date To END Press ExitSET Manual Clock Time Month To Correct Press Clear To END Press ExitAutomatic PBS Channel Selection Setting the Clock cont’dPRIM. Setup Press B VCR Program VCR Setup Caption Reminder BrightnessSET Auto Clock Time NOW Searching flashes on the TV/VCR screenWait for the TV/VCR to find the time SET Auto Clock Time Date NOW Searching To END Press ExitManual PBS Channel Selection Use the Number buttons to select your PBS station Press the PLAY/ button or the STOP/ button to select PRIM. SETUP. Then, press the F.FWD/B buttonPRIM. Setup Press B VCR Program VCR Setup Daylight-Savings TimePress the Menu button, then press the STATUS/EXIT button Primary SetupVolume BAR SET Clock Select KL Choose B To END Press Exit Time ZoneFront Panel Connect your antenna or cable here. Details are on page six AC Power CordRear Panel ANTenna JackRemote Control Buttons STOP/ Button Menu ButtonSTATUS/EXIT Button REWind/ ButtonWhen you finish, press the STATUS/EXIT button Adjusting the Picture ControlsDecreased brightness Adjusting the Picture Controls cont’dTint KK Sharpness TV Reset Decrease IncreaseIf you select Status OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status ON, then select Counter only onOFF ReminderFollow the steps below to play a tape PlayingInsert a tape in the TV/VCR Hrs RecordingRead and follow the steps below to record a TV program To stop recording, press the STOP/ button Tape SpeedsPress the STOP/EJECT but- ton on the TV/VCR to stop the OTR Length Press OTR Cancel Press ClearOne-Touch Recording Tape is in the TV/VCR. The record tab must be intactRerecording Tape Duplication TV/VCR is now in Line Input modeDaily Timer RecordingSelect Program Number To END Press Exit Time OFF To Correct Press Clear To END Press Exit ONE Time Program Channel Time onTimer Recording cont’d Gram Review and press the F.FWD/B button Timer recording information for the program in the lowestWith the TV/VCR on, press the Menu button Program REVIEW, then press the F.FWD/B buttonREC Defeated VCR Setup ONE Time PlayDefeat Recording Follow the steps below to prevent accidental recordingTV programming will appear while the tape is rewinding VCR SETUP, then press the F.FWD/B buttonVCR Setup ONE Time Play Repeat Play on Repeat PlayB Repeat Play VCR Setup ONE Time Play Repeat Play A-BInsert a tape in the TV/VCR Press the Menu button Repeat Repeat Play cont’dAppear on the screen Real-Time Counter MemoryStop Super High Speed Searching LP/SLP Forward and Reverse Searching SP/LP/SLPViewing a Still Picture To block ratings, follow the steps below SmartLockSmartlock menu will appear Ratings are defined on SmartLock cont’dExample Specific Sub-ratings After you enter the code, the Smartlock menu will appear To change the access code, follow these stepsTV-Y7 TV-G Blocked RatingsBlue Background VCR Program VCR Setup Caption ReminderTimer during a recording Sleep TimerPress the SLEEP/WAKE UP button Timer Sleep Wake UP TV on ON-TIME Wake Up TimerTimer Sleep Wake UP VCR Program VCR Setup Caption Volume BarMenu Screen To Adjust Press / B CaptionClosed Caption ExampleStandard Closed Captions Closed Caption cont’dHalf-screen text Automatic Operation Features Glossary Helpful Hints Helpful Hints cont’d Specifications Please contact Philips at French Speaking English Speaking Limited WarrantyModel # Serial # Index Page Supplied Accessories
Top Page Image Contents