Memorex MVT2195B, MVT2135B Loading and Unloading a Video Cassette, Automatic Power on and Play

Page 35

LOADING AND UNLOADING A VIDEO CASSETTE

Use only video cassette tapes marked .

LOADING

Push the center of the tape until it is automatically retracted into the TV/VCR.

AUTOMATIC POWER ON AND PLAY

When loading a cassette tape without the erase prevention tab intact, the TV/VCR will turn on automatically and playback will start immediately.

Insert the cassette with its labeled side facing you.

An inverted video cassette cannot be inserted.

ENGLISH

1

UNLOADING

2

1	To unload a video cassette, press the EJECT
	button on the remote control, or press the Stop/

Eject button on the TV/VCR twice. The first press will stop the tape in any mode. The second press will eject the tape.

EJECT Stop/

OEject

OR

AUTOMATIC EJECT

If the TV/VCR automatically rewinds the tape to the beginning (AUTO REWIND FEATURE), the tape will be ejected automatically. (See NOTE on page 40.)

2 Pull the cassette out.

NOTES: • Always eject the tape when not in use.

•The cassette tape can be ejected even if the POWER is “OFF”.

33

545A201A-E/P30-39

33

19*04*0, 17*10

Image 35

Contents MVT2135B MVT2195B English Read Instructions CleaningAccessories Power SourcesReplacement Parts POWER-CORD ProtectionPower Lines Damage Requiring ServiceNEC Section Safety CheckWall or Ceiling Mounting HeatFeatures Table of Contents Moisture will Condense on the Unit in the Following Cases PrecautionsWhen YOU Experience the Above Conditions Moisture CondensationAC Outlet Power SourceTo USE AC Power Source Cassette Loading Slot To insert or remove a video tape AC Power Cord Connect to a 120V, 60Hz outletPower Indicator Lights when the power is turned on Location of ControlsMenu Remote ControlPaying attention to Polarity diagramBattery compartment ArrowCombiner UHF 300 ohm VHF 300 ohm Antenna ConnectionsMatching Indoor Antenna Cable TV Connections For Subscribers to Basic Cable TV ServiceFor Subscribers to Scrambled Cable TV Service Normal TV viewing Setting the LanguageEnter button To SET Auto Clock to OFF Auto Clock SettingAuto Clock Setting Auto Clock AdjustmentPress the Menu button until the Menu screen is cleared Press the Menu button. Press the SETPress the Enter button Press the SET/TRACKING Manual Clock SettingExample Setting the clock to 830 AM, 23rd. MON October To move cursor backward, press the Cancel buttonVHF/UHF Channels Adjust the volume level byTV Operation To turn on the TV/VCRCall MutingChannel + Quick View SleepTV/CAPTION/TEXT To View Closed Captions What is Closed CAPTIONING?Closed Captioning with a VCR To Memorize Channels TV/CATV modeSelected mode Screen is cleared Automatic Memory TuningChannels available in your area Or Channel + or button Using SET/TRACKING + orTo ADD/DELETE Channels Again for the safety, then Setting the V-CHIPTo Register Password Enter the same passwordTo SET the V-CHIP Under 17 years old Movie Rating is not setAll ages PG-13 Parental guidance Less than 13 years oldTo Change Password Set the desired minute To SET the on Timer+ or button to set Desired hour, then press the Enter buttonExample Turning off the TV at 1130 PM To SET the OFF TimerMenu button Picture Control AdjustmentsBrightness ContrastPress the Enter button until Sharpness appears Sharpness CancelButton to adjust the sharpness of the picture Preset levels Color TintUnloading Automatic Power on and PlayLoading and Unloading a Video Cassette LoadingTape Speed and Maximum Playback / Recording Time To Prevent Accidental Erasure To Record AgainTo play a prerecorded tape PlaybackTo Start Playback To Stop PlaybackFORWARD/REVERSE Picture Search To Rewind or Forward the Tape RapidlyDigital Tracki NG Control Skip Search To Watch Still Picture Special PlaybackTo Visually Search for Desired Points Speed Search TimesPosition Repeat mode is canceledTo Watch a Tape Repeatedly Select the Auto Repeat optionRecording and Viewing the Same TV Program Recording a TV ProgramPress the REC/OTR button Screen and the Rec/Otr indicator will lightTo Stop Recording To Stop Recording Temporarily To be recorded. Example ChannelTV/VCR channel cannot be changed during recording ONE-TOUCH Timer Recording OTRSelect the Program position, then press Timer RecordingCheck the Timer REC SET option is selected Then press the Enter buttonRecording is automatically started To set the timer for another program, pressIndicator will light. The Timer is programmed When the programmed time is reached,Example Other Functions for the Timer RecordingTo SET DAILY/WEEKLY Timer To Confirm the SettingsProgram Deleted Parts Recording Prog.1 Prog.2 Prog.3 Control SettingsCounter to Using the Real Time Tape CounterTo View the Counter Display Tape CounterUsing Zero Return Tion tab intact into the TV/VCR Duplicating a Video TapeConnection to Another VCR Connection to CamcorderIgnition Reception DisturbancesTV Broadcast Reception Troubleshooting GuideSymptoms Cause Possible Solutions Power No powerPlayback Symptoms Cause Possible SolutionsRemote Control RecordingSnowy Picture Video Head CleaningVCR SpecificationsAccessories TelevisionMemo Español 545A201A K 00/03