Toshiba SD-260SV, SD-260SY, SD-260SA manual Connecting to Optional Equipment

Page 18

Connections

Connecting to Optional Equipment

You can enjoy high quality dynamic sounds by connecting the DVD video player to optional audio equipment.

• For connection to your TV, see “Connecting to a TV”

1617 .

For details of output sound, see 41 .

This section uses the following reference marks.

: Front speaker

: Rear speaker

: Sub woofer

: Center speaker

: Signal flow

Notes

DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player to the AC-3 RF input of a Dolby Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player.

Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player to the “DIGITAL (COAXIAL)” input of a Receiver or Processor.

Refer to the owner’s manual of the connected equipment as well.

When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections.

The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.

Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power on, the speakers may be damaged.

Warning

When you are connecting (via the COAXIAL DIGITAL AUDIO OUT jack) an AV decoder that does not have Dolby Digital, Digital Theater Systems (DTS) or MPEG2 decoding function, be sure to set “Digital Output” to

“PCM” from the on-screen displays 50 55 . Otherwise, high volume sound may damage your hearing as well as the speakers.

When playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog audio output jacks. To avoid possible damage to the audio system, you should take proper precautions when the analog audio output jacks of the DVD video player are connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player.

18

Image 18
Contents SD-260SV SD-260SA SD-260SY This Digital Video Disc Player employs a Laser System May result in hazardous radiation exposureLocation of the required label Important Safety Instructions S3125A Additional Safety Instructions Introduction Precautions To obtain a clear pictureOn handling discs On cleaning discsStructure of disc contents On storing discsOn Video CDs Playable discsTable of Contents Identification of Controls Front panelRemote control Operating with the remote control Loading batteriesOpen the cover Insert batteries R03/AAA size Connections Connecting to a TV Connecting to a TVInterlaced outputs Progressive outputsConnecting to Optional Equipment Dolby Digital Dolby Surround Pro LogicConnecting to an amplifier equipped with a DTS decoder Digital Theater Systems DTSMPEG2 sound Channel digital stereo Basic playback Playing a Disc Basic playbackAutomatic Power Off function To pause playback still modeTo turn the power off To enter the standby mode To obtain a higher quality picturePlaying frame by frame Variable Speed PlaybackPlaying in fast reverse or fast forward directions Press REV or FWD during playbackPress Slow during playback Playing in slow-motionResuming playback from the same location Press PlayPress TOP Menu DVD Locating a title using the top menuLocating a Desired Section Press / / / to select the title you wantPress T Press / to highlight the Title/Chapter or Track Accessing chapters/tracks using number buttonsLocating a specific chapter or track Press / to select a section you want to locateAdvanced playback Press T Accessing a Specific Location DirectlyEntering the time counter of the desired location Press the number buttons to enter TimeRepeating a Specific Segment Repeating a specific segmentPlaying titles, chapters or tracks in a varied order Press Play ModePlaying in a Varied Order Press PlaySetting titles, chapters, or tracks in a favourite order Playing in a Favourite OrderInsert a disc and press Memory during stop Zooming a Picture Zooming a picturePress Zoom during normal, slow or still playback Press E.P.M Selecting the Picture Enhancement E.P.MSelecting the picture enhancement To exit the picture enhancement selectionPress E.A.M Selecting the Sound Enhancement E.A.MSelecting the sound enhancement To exit the audio enhancement selectionSelecting the Camera Angle Changing the camera anglePress Subtitle during playback Selecting SubtitlesDVD Selecting a subtitle language To turn subtitles on or offPress Audio during playback Selecting a playback audio settingSelecting a Language Selecting sound channels of Video CDsOn-screen display operation FeaturesOn-screen Display Operation Press NaviViewing the operational status Bit rate Mbit/sOn the disc tray Playing MP3/WMA filesPlace a CD that contains MP3/WMA files Press OPEN/CLOSE to load the discPlayable files Viewing Jpeg Files Viewing Jpeg filesTurn the page if necessary Viewing a thumbnail viewPress TOP Menu in full-screen review Press PAUSE/STEP during playbackJpeg files compatibility Function setup Customizing the Function Settings Table of LanguagesRepeat steps 3 and 4 to change other Settings Customizing the Function SettingsSetting procedure Press SetupTo select a preferred language for subtitles Audio To turn the parental lock function on or off DefaultVideo, Audio and etc. to the factory default To select a preferred language for the sound Track DVD MenuSetting details OSD MenuAudio TV Shape Digital Output Default Abbreviation Language Table of LanguagesTable of languages and their abbreviations LanguageBefore Calling Service Personnel Specifications OthersBefore Calling Service Personnel Symptoms and correctionSupplied Accessories SpecificationsDVD video player / outputs / supplied accessories DVD Video PlayerMemo Memo 811-S26091-011