Toshiba 32HL85 owner manual Adding channels to the TVÕs memory, Programming channels automatically

Page 24

Setting up your TV

Adding channels to the TVÕs memory

When you press Channel y or z, your TV will stop only on the channels you programmed into the TVÕs channel memory.

Follow the steps below and on the next page to program channels into the TVÕs memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in the channel memory. After the channels are programmed automatically, you can manually add or erase individual channels (see page 25).

To program channels automatically:

1.Press MENU, and then press x or • until the SET UP menu appears.

2.Press y or z to highlight TV/CABLE.

3.Press x or • to select either TV (if you use an antenna) or CABLE (if you use cable channels).

SET UP	1/2
LANGUAGE	ENGLISH

TV/CABLE	CABLE

CH PROGRAM	ENTER

ADD/ERASE	ADD

CH LABELING	ENTER
VIDEO LABEL

MENU BACK EXIT WATCH TV

4. Press z to select CH PROGRAM.

SET UP	1/2
LANGUAGE	ENGLISH
TV/CABLE	CABLE
CH PROGRAM	ENTER
ADD/ERASE	ADD
CH LABELING	ENTER
VIDEO LABEL

MENU BACK EXIT WATCH TV

5.Press ENTER to start channel programming. The TV will automatically cycle through every channel (TV or Cable, depending on which you selected in step 3), and store all active channels in the channel memory.

While the TV is cycling through the channels, the message ÒProgramming NowÑPlease WaitÓ appears.

6.When channel programming is complete, the message ÒCompletedÓ appears.

7.Press Channel y or z to view the programmed channels.

Note:

To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

TV/VIDEO	RECALL	POWER
TV/VIDEO	RECALL
	INFO
1	2		3
4	5		6	Channel
7	8		9	Channel
7	8		9	Numbers
+10		CHRTN
100	0		ENT
U	FAV
	FAV
				MENU
	DVDMENU			yzx •
				yzx •
	FAV			R
	FAV			ENTER
				ENTER
CH		VOL		Channel yz

24

Image 24

Contents 32HL85 Safety Precautions Dear CustomerImportant Safety Instructions InstallationService Care cont. from previous columnImportant notes about your LCD TV Introduction Supplied accessories Check that you have the accessories and items shownIntroduction Welcome to ToshibaTV/VIDEO Menupower Exploring your new TVConnecting your TV Connecting an antenna or cable TVChannels Connecting a VCR Connecting a cable converter box and VCRConnecting a DVD player or satellite receiver and a VCR DVD player with component video TV upper back panel TV lower back panel From DTV Antenna Connecting two VCRs Connecting a camcorderConnecting an HDMIª or a DVI device to the Hdmi input ¥ one Hdmi cable type a connector¥ one HDMIÐtoÐDVI adapter cable Hdmi type a connector ¥ one pair of standard analog audio cablesUsing the remote control Preparing the remote control for useInstalling the remote control batteries Remote control effective rangeRemote control codes For future reference, write down the codes you usedRemote control codes Setting Your UsingtheTVÕs Features Appendix Index Remote Control function key chart CLEAR/EXIT Learning about the remote control Mute reduces or turns off the soundSetting up your TV Learning about the menu systemChanging the on-screen display language Press x or to display your desired languageAdding channels to the TVÕs memory Programming channels automaticallyPress z to select CH Program Changing channels Adding and erasing channels manuallyUsing the TVÕs features Adjusting the channel settingsSwitching between two channels using Channel Return Programming your favorite channelsConnecting Labeling channels Viewing the wide-screen picture formats Selecting the picture sizeFull picture size TheaterWide 1 picture size For 43 format programs ¥ None of the picture is hiddenAdjusting the Picture Position Press MENU, and then press x or until the SET UPPress x or to adjust the settings as required Menu appearsSetting the Hdmi audio mode Using the Auto Aspect featurePress y or z to highlight Auto Aspect Press x or to select onUsing the gray screen function Selecting the gray level for 43 mode side panelsTo turn on the gray screen function To turn off the gray screen function Select OFF in aboveUsing the Locks menu Using the V-CHIP menuEntering the PIN code If you cannot remember your PIN codeOFF To release your setting Unlock TV Rating Independent rating system for broadcastersTV Rating menu appears Press z or y to select an item Repeat steps 2 and 3 to set the next itemMpaa Rating Independent rating system for movies Chip menuLocking channels Unlocking programs temporarilyRepeat steps 2 and 3 for other channels Repeat for other channels Locking the video inputs Changing the PIN codeAdjusting the picture Selecting the picture modeAdjusting the back light feature Press x or to select the mode you preferAdjusting the picture quality Using the black stretch featureUsing the Mpeg NR feature Using the CableClear¨ DNR featurePress x or to select LOW, MIDDLE, HIGH, or OFF Press x or to select LOW, MIDDLE, HIGH, or AutoSelecting the color temperature Selecting the cinema modeSelecting the video input source Labeling the video input sourcesUsing the closed caption feature Press x or to highlight C1-C4 or T1-T4¥ To view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timerAdjusting the sound Muting the soundSelecting stereo/SAP broadcasts Using the WOWª surround sound feature Adjusting the sound quality Using the StableSound¨ featurePress x or to adjust the level To turn off the StableSound feature Select OFF in aboveUnderstanding the auto power off feature Understanding the last mode memory featureDisplaying on-screen information Specifications AppendixTroubleshooting AntennaBlack box appears on the screen T2, T3, or T4. Turn closed captioning OFFLimited United States Warranty Limited Canada Warranty Index Channel programmingToshiba ELECTROMEX, S.A. DE C.V