Toshiba 37X3000A Setting the HDMI1 audio mode, Connecting an Hdmi device, Connecting a DVI device

Page 36

Connecting your TV

Connecting an HDMI device

One HDMI cable (type A connector)

TV back view

HDMI device

VIDEO AUDIO

L R

IN

HDMI OUT

OUT

For proper operation, it is recommended that you use a short HDMI cable.

HDMI cable transfers both video and audio.

Note:

It is possible that some HDMI device may not operate properly with this TV.

Connecting a DVI device

One HDMI (type A connector)-to-DVI adapter cable and audio cables

TV back view

TV back view

PC/HDMI1

(AUDIO)

DVI device

VIDEO	AUDIO		DVI
	L	R	OUT
			IN
			OUT

HDMI (type A connector)-to-DVI adapter cable

For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 3m. The recommended length is 2m.

Standard analog audio cables

An HDMI-to-DVI adapter cable transfers only video.

Separate analog audio cables are required.

Note:

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

Selecting the PC/HDMI1 audio mode

You can select PC audio or HDMI1 audio when using this function (- page 35).

1Press M, then press or to display the SET UP menu.

2Press or to select AV connection, then press Q to display the AV connection menu.

AV connection

PC/HDMI1 audio		PC

HDMI1 audio		Digital

AV output		ATV

MENU Back EXIT Watch TV

3Press or to select PC/HDMI1 audio, then press or to select PC or HDMI1.

Setting the HDMI1 audio mode

You can select sound of an HDMI or DVI device connected to the HDMI1 input terminals (- page 35) from three modes: Auto, Digital or Analog.

Note:

This function is available only when the PC/HDMI1 audio mode is set to HDMI1.

1From the AV connection menu, press or to select

HDMI1 audio.

AV connection

PC/HDMI1 audio		HDMI1

HDMI1 audio		Auto

AV output		ATV

MENU Back EXIT Watch TV

2Press or to select Auto, Digital or Analog.

When the sound is not audible:

If no sound comes out while receiving HDMI signal, the sound may be audible when using this function set to off.

1From the HDMI1 audio item in the AV connection, press and hold Q until the Lip Sync Latency menu appears on the screen.

Lip Sync Latency

On

2Press or to select Off.

3Press on the remote control or ! on the TV right side panel to switch to the standby mode.

4Press on the remote control or ! on the TV right side panel again to switch the power on.

Note:

Depending on some external equipment, the sound may be audible by turning it off and on again.

36

Image 36

Contents 37X3000A 42X3000A 46X3000A 52X3000A Contents Important Safety Instructions InstallationIntroduction Welcome to ToshibaPrecautions for moving the TV Precautions for installing on outdoor antennaUse Never stand or climb on the TVService Never repair, modify or disassemble the TV by yourselfCleaning Important informationConnecting an antenna Installing the remote control batteriesGetting started Exploring your new TVTV front and side panel controls TV top view TV front viewTV back panel connections Digital Audio Optical output terminalDigital Audio Coaxial output terminal Learning about the remote control Location of controlsTuning the TV for the first time Switching on the TVSwitching off the TV Turning the TV onDisplaying the Digital Setting chart Displaying the TV Setup menu chartThis menu will display only Digital TV selected Programming channels into the TV’s channel memory Press Q to display the Auto tuning menu Programming channels automaticallyPress Q to start the automatic search Search will begin for all available stationsManually setting channels in the channel memory Program position selection Sound system Color systemWatching TV programs Setting the Time Format Sorting program position -analog onlyDolby D Press to select the new position 4, then pressUsing the TV’s features General Picture adjustmentSelecting the picture size Using the picture still Adjusting the picture position analog onlyResetting the picture position analog only Selecting the picture modeAdjusting the basic picture quality Selecting the color temperatureAdjusting the color management Activating the black stretchResetting the base color adjustment Using the active backlight controlUsing the cinema mode analog only Using the auto formatSound adjustment Selecting the dual 1 or dual 2 modeAdjusting the sound quality Selecting the bilingual programs analog onlyUsing the SRS WOW surround sound Using the stable soundUsing the bass boost Adjusting the brightness of side panelTimers Setting the Time zone digital onlyTo delete a selected entry Setting the Alarm digital only Setting the sleep timerSelecting the video input source to view Once, Mon-Fri or DailySetting up the teletext mode Teletext in Analog TVTeletext general information Using Auto mode Using List modePress the Green button and enter the 3-digit number Teletext buttons on the remote control Teletext in Digital TVOther Digital TV features and settings Setting the EPG Electronic Program guidePassword Setting the PasswordSetting the parental rate Setting favorite, locking and skipping channelsParental rate Channel listFavorite Mode Restore factory settingRestore Factory Setting, then press Q SubtitleTV Setup Audio PreferenceTransparency Connecting your TV Connecting an audio system digital only Back connections Connection exampleConnecting an amplifier equipped with an Mpeg decoder To Optical or Coaxial typeConnecting an Hdmi or a DVI device Side connectionsSetting the HDMI1 audio mode Connecting an Hdmi deviceConnecting a DVI device Selecting the AV output mode Connecting a computerFollowing signals can be displayed To connect a PC to the RGB/PC terminal on the TVUsing the PC setting Adjusting the clock phase of the pictureAdjusting the picture size/position Adjusting the sampling clockTroubleshooting Symptom and solutionSymptom and solution digital only Reference sectionAppendix Australian Parental Guidance Codes NormativeSpecifications Broadcast systemBroadcast transmission systems of each country or region Integrated Digital LCD TVTemperature 35 C Humidity 10 W + 10 W 10 % THDMain Ø 100 mm 2 pcs Input