Toshiba 42hl167 manual Using the remote control, Installing the remote control batteries

Page 23

Chapter 3: Using the remote control

Installing the remote control batteries

To install the remote control batteries:

1 Slide the battery cover off the back of the remote control.

2 Install two “AA” size alkaline batteries. Match the + and

symbols on the batteries to the symbols on the battery compartment.

3 Slide the battery cover on to the remote control until the lock snaps.

Caution: Never throw batteries into a fire.

Note:

Be sure to use AA size alkaline batteries.

Dispose of batteries in a designated disposal area.

Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.

If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones.

When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.

Always remove the batteries from the remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.

Remote control effective range

For optimum performance, aim the remote control directly at the TV remote sensor. Make sure there are no obstructions between the remote control and the TV.

Point remote control toward remote sensor on front of TV.

16.4 ft (5m)

23

Image 23
Contents 42HL167 47HL167 Dear Customer Safety PrecautionsInstallation Important Safety InstructionsInstallation, Care, and Service Additional Safety PrecautionsCare ServiceRemoving the Pedestal Stand To Display your LCD TV using a Wall BracketChoosing a location for your LCD TV To Display your LCD TV on the included Pedestal StandTrademark Information PartImportant notes about your LCD TV Contents Troubleshooting Welcome to Toshiba Features of your new TVIntroduction Introduction HD1, ColorStream HD2, Hdmi 1, Hdmi 2, Hdmi 3, PC TV front and side panel controls and connectionsGreen and Yellow LEDs ColorStream HD-1 and ColorStream HD-2 TV back panel connectionsAbout the connection illustrations Connecting your TVOverview of cable types To view the VCR Connecting a VCR and antenna or Cable TV no Cable boxTo view the antenna or Cable signal You will needStandard audio cables Connecting a VCR with S-video and a cable boxTo view basic and premium Cable channels Coaxial cables Video cableTo record a TV program while watching a DVD To view antenna or Cable channelsTo view the DVD player To view the VCR or view and record antenna channelsIf you cannot locate the device’s infrared sensor To connect the IR blaster cableTo control the devices Select the Video 2 video input source on the TV Connecting a camcorderTo view the camcorder video To connect a DVI device, you will need Connecting an Hdmi or DVI device to the Hdmi inputTo connect an Hdmi device, you will need To view the Hdmi device videoThree Hdmi cables CE-LINKconnectionBefore controlling the devices To control the audio Connecting an audio systemTo connect a PC to the Hdmi terminal on the TV Connecting a personal computer PCFormat Resolution Frequency To connect a PC to the PC in terminal on the TVTo install the remote control batteries Using the remote controlInstalling the remote control batteries Remote control effective rangeTheaterWide 1/2/3, Full, 43 HD, and Native Learning about the remote controlSatellite DVD Remote Control functional key chartCombo Receiver CH RTN Mode Select Device mode control after programming Using the remote control to operate your other devicesDevice code setup Mode Select Default device mode control before programmingTo reset the remote control Using the volume lock featureOperational feature reset To unlock the remote control’s volume keysSatellite receivers TVsCable boxes 3D LAB DVDsVCRs DVD/VCR ComboKEC STS Audio Amp PVRsCable/PVR Combo DBS/PVR ComboSAE Audio Amp/TunersIcon Option Menu layout and navigationMain menu layout Thinc menu Setup/Installation menu layoutSetup menu InstallationVideo Navigating the menu systemTo select the menu language Setting up your TVTo configure the ANT input source Selecting the menu languageTo add or delete channels in the channel memory Programming channels automaticallyManually adding and deleting channels in the channel memory To program channels automaticallySetting the Auto Input feature To assign channel labels To reset Auto InputLabeling channels To turn off the Auto InputTo delete the custom label Setting the Hdmi audio modeTo set the Hdmi audio mode To remove channel labelsViewing the system status Viewing the digital signal meterReset Factory Defaults Highlight No and press T Selecting the Power-On ModeTo cancel the reset To set the Power-On Mode featurePress CABLE/SAT, DVD, or VCR/PVR Using the TV’s featuresLabeling the video input sources To label the video input sourcesFavorites Browser Tuning channelsTuning channels using Channel Browser Adding and clearing channels and inputs in the History List Elements of the Channel BrowserSwitching between two channels using SurfLock Tuning to a specific channel programmed or unprogrammedSwitching between two channels using Channel Return TheaterWide 2 picture size for letter box programs Selecting the picture sizeNatural picture size TheaterWide 1 picture size for 43 format programsFull picture size for 169 480i, 480p source programs only To set the scroll settingsUsing the Freeze feature Adjusting the picture quality Adjusting the pictureSelecting the picture mode To view captions or text Using the closed caption modeDigital CC Settings Base closed captionsCC Selector Adjusting the audioUsing the Closed Caption button on the remote control Using the digital audio selectorMTS field, select Stereo Press C or c to adjust the levelSelecting stereo/SAP broadcasts To listen to stereo soundUsing the Dolby Digital Dynamic Range Control feature Using the StableSound featureChanging your PIN code Using the Locks menuEntering the PIN code If you cannot remember your PIN codeTo download the additional rating system if available Press b to highlight Enable Rating BlockingBlocking TV programs and movies by rating V-Chip To block and unblock TV programs and moviesTo unblock individual channels Blocking channelsTo block channels Unlocking programs temporarily Using the input lock featureUsing the control panel lock feature Using the GameTimerTo set the PC Audio Using the PC settings featureSetting the PC Audio To adjust the PC settingsCE-LINK playback device HD DVD player, etc. control Setting the sleep timerUsing CE-LINK Other CE-LINK functions Volume and Mute controls of Audio ReceiverTo set the CE-LINK Setup To display TV status information using Info Understanding the auto power off featureUnderstanding the last mode memory feature To display TV status information using RecallUsing the static gamma feature Using the TV’s advanced featuresUsing the advanced picture settings features Using dynamic contrastTo change the CableClear settings Selecting the color temperatureUsing CableClear digital noise reduction To select the color temperatureUsing Color Palette Adjustment Using Mpeg noise reductionUsing the ColorMaster feature To turn off Game Mode Using the Game Mode featureTo reset ColorMaster to its factory settings To turn on Game ModeHighlight Advanced Audio Settings and press T Using the advanced audio settings featuresUsing the SRS WOW surround sound feature To adjust the WOW settingsGeneral troubleshooting TroubleshootingNo CE-LINK operation Channel tuning problemsClosed caption problems Rating blocking V-Chip problemsLED indications LED Indication Condition SolutionAppendix SpecificationsPin No Signal name For LCD Televisions 26 and Larger Limited United States WarrantyFor Toshiba Brand Flat Panel Televisions Limited Canadian WarrantyDisclaimer and Limitation of Remedy Appendix Freeze IndexPage 07-03
Related manuals
Manual 82 pages 12.32 Kb Manual 82 pages 11.23 Kb