Toshiba 65H14 owner manual Adding channels to the TV’s memory, Programming channels automatically

Page 24

Adding channels to the TV’s memory

When you press Channel		or , your TV will stop only on the	Note:
	y	z	Note:
channels stored in the TV’s channel memory.			To tune the TV to a channel not programmed
Follow the steps below and on the next page to program all active			in the channel memory, you must use the

	channels into the TV’s memory.	Channel Number buttons on the remote
	channels into the TV’s memory.	control.
		control.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are stored automatically, you can manually add or erase individual channels (see page 25).

To program channels automatically:

1.Press MENU, and then press x or • until the SET UP menu appears.

2.Press y or z until the TV/CABLE is highlighted, and then press ENTER to display the pull-down menu.

3.Press y or z to highlight either TV or CABLE, depending on which you use. If you use an antenna, highlight TV; if you use cable, highlight CABLE.

TV/VIDEO RECALL POWER

INFO

1 2 3

4 5 6

7 8 9

+10CHRTN

100 0 ENT

Setting tup your TV

LANGUAGE	SET UP
LANGUAGE	TV
CLOCK SET	CABLE
ANT 1 / 2
TV / CABLE
CH PROGRAM
ADD / ERASE
: SELECT	ENTER : SET

4.Press ENTER.

5.Press z to select CH PROGRAM.

	SET UP
LANGUAGE		ENGLISH

CLOCK SET		0 0 : 0 0
ANT 1 / 2		ANT1
TV / CABLE		CABLE
CH PROGRAM
ADD / ERASE		ADD

			N					G
			E	U	FAV			UI
		P	M	ORITE	FAV		PIC	D
	O	P		ORITE			PIC		E
T	O						SI
T			FAV				SI
			FAV					ZE
					MENU
					DVDMENU
NENTER							EXIT			R
		T								R
E									EA
		E			FAV				EA
			R					L
			R					C
	TV				CH	VOL
	CBL/SAT				CH	VOL
	VCR
	DVD
				POP DIRECT CH MUTE			SLEEP
TV/VCR					PAUSE	STOP	PLAY
					FREEZE	SOURCE	SPLIT
		REW			FF	SKIP/SEARCH
CH SCAN					SWAP	POP CH

RECLIGHT

MENU

yzx •

ENTER Channel yz

: MOVE ENTER : START

6.Press ENTER to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory.

While the TV is cycling through the channels, the message “Programming Now—Please Wait” appears.

7.When channel programming is complete,the message “Completed” appears.

8.Press Channel y or z to view the programmed channels.

24

Image 24

Contents Projection Television Safety Precautions Dear CustomerImportant Safety Instructions InstallationService CareImportant Safety Precautions for Split Cabinet Feature Important Safety Information Introduction Welcome to Toshiba Exploring your new TVConnecting your TV Connecting in Antena or cable TVConnecting a VCR Connecting a cable converter boxYou will need Three coaxial cables Connecting a cable converter box and VCR You will need Four coaxial cables One set of A/V cablesConnecting a DVD player or satellite receiver and a VCR Satellite Satellite Receiver DishFrom Antenna Stereo VCR From DTV Antenna Connecting two VCRs Connecting a camcorderYou will need Two coaxial cables Two sets of A/V cables One Hdmi cable type a connector One pair of standard analog audio cablesConnecting an audio system Preparing the remote control for use Installing the remote control batteriesIf you have a Toshiba device Remote control codes Htib 100 Learning about the remote control Adjusts the volume levelPOP Direct CH allows direct access to POP channels CH RTN returns to the memorized channelPress Enter to activate the function settings in the menus Learning about the menu systemChanging the on-screen display language Selecting the antenna inputPress y or z to highlight your desired language Adding channels to the TV’s memory Programming channels automaticallyPress Enter Press z to select CH Program Press Channel y or z to view the programmed channelsChanging channels Adding and erasing channels manuallyAdjusting the color convergence Manually adjusting the color convergenceWhen the adjustment is complete, the normal picture appears AutomaticallyTo reset your adjustments 100Adjusting the channel settings Switching between two channels using Channel ReturnSwitching between two channels using SurfLock Programming your favorite channelsPress Enter Repeat steps 4 and 5 for other channels Press y or z to highlightFavorite CH Labeling channels Repeat to enter the rest of the charactersTo erase channel labels Press z or y to highlightPress PIC Size on the remote control Selecting the picture sizeHidden areas, see Scrolling Theater Wide picture on None of the picture is hiddenPress PIC Size to select the Theater Wide 2 or 3 mode Press Enter to display the Scroll Adjustment modePress MENU, and then press x or until Picture menu AppearsUsing the Auto Aspect feature Press y or z to highlight Auto ASPECT, and then pressEnter Press y or z to select ON, and then press EnterUsing the POP double-window feature To close the POP window Press Split again or ExitSwitching the main and POP pictures Switching the speaker sound of main and POP programsSelected input source indicator is displayed in purple Using the programmed channel search function Double-Window aspect ratioUsing the favorite channel search function About the auto favorite featureUsing the Locks menu Using the V-CHIP menuEntering the PIN code If you cannot remember your PIN codeEnable Blocking TV Rating Independent rating system for broadcastersMpaa Rating Independent rating system for movies Mpaa RatingMpaa Unrated TV None RatingLocking channels Unlocking programs temporarilyPress Enter Repeat steps 3 and 4 for other channelsPress y or z to highlight Clear ALL, and then press Enter Locking the video inputs Changing the PIN codeOFF Press Enter New PIN code is now activeAdjusting the picture Selecting the picture modeAdjusting the picture quality Selecting the color temperature Press x or to select the mode you preferSaving your new preferences Using the CableClear DNR feature Resetting picture adjustmentsReset DoneSelecting the display format for 480p signals only Selecting the cinema modePress y or z to select FilmSelecting the video input source To changeUsing the closed caption feature Press y or z to highlight Caption or TEXT, and then pressSetting the on timer Setting the sleep timerSetting the clock Press Enter to start the clockTo display the time on-screen Press Recall Adjusting the sound Muting the soundSelecting stereo/SAP broadcasts Press y or z to highlight MTS, and then press EnterUsing the WOW surround sound feature Adjusting the sound qualityPress y or z to adjust the item, then press Enter Audio Settings menu appearsResetting your audio adjustments Using the StableSound featureTo turn off the StableSound feature Select OFF in above Turning off the built-in speakers Selecting the Audio OUT soundTo turn on the built-in speakers Select on in above Press y or z to select Main or POP, and then press EnterUnderstanding the auto power off feature Understanding the last mode memory featureSelecting the background of the menu display Displaying on-screen informationSpecifications AppendixTroubleshooting Limited United States Warranty Limited Canada Warranty Index Page Manufactured by