Toshiba D-R17DTKB owner manual Timer Recording

E7J70BD_EN.book Page 39 Monday, May 7, 2007 3:31 PM

Timer Recording

Video	VR
DVD-RW	DVD-RW DVD-R DVD+RW

DVD+R

You can set the unit to record up to 12 programmes, up to a month in advance. Daily or weekly programme recordings are also available.

•Be sure to set the clock before entering a timer programming.

Insert a recordable disc.

1 In stop mode, press [TIMER PROG.]. Timer Programming list will appear.

2 Select “New Program” using [U / D], then press [ENTER/OK].

Timer Programming

0:00 THU 06/12

Date	Start	End	CH	STTL
				PDC
06/12	7:00	9:00	18
07/12	9:00	9:30	190

New Program

1/1

•If there are 7 programmes or more, use [SKIP B / F] to turn the page.

3 Enter the date using [U / D], then press [P].

Each time you press [D] at the current date, the timer recording date will change as follows.

e.g., 1st January

01/01

Daily

M-F (Mon.-Fri.)

W-SAT

W-FRI

W-SUN

31/01

Timer Programming

0:00 THU 06/12

	Date		Start		End
	01/01	- - : - -			- - : - -
	CH		Mode		PDC
901			SP		OFF
				SP	2:00

1/1

4 Enter the time to start and to end

using [U / D], then press [P].

5 Select the channel number to record using [U / D], then press [P].

To record from the external input, select “AV1”, “AV2”, or “AV3”.

6 Select the recording mode using [U / D], then press [P].

Refer to “Recording Mode” on page 32.

7 For DVB channel recording: Select “STTL” to “ON” or “OFF” using [U / D].

If you set “STTL” to “ON”, subtitle will be recorded too.

•When analogue channel is selected, “PDC” will be displayed instead of “STTL”.

For analogue channel recording: Select “PDC” to “ON” or “OFF” using [U / D].

Refer to “PDC (Programme Delivery Control)” on page 40.

•When DVB channel is selected, “STTL” will be displayed instead of “PDC”.

8 Press [ENTER/OK] when all information required is entered.

Your programme setting is stored.

•To set another programme, repeat steps 2 to 8.

•To exit, press [TIMER PROG].

•When 2 or more programmes are overlapped, “Timer program overlapped” appears, and the overlapped programme will be displayed in blue. To correct the timer programme, refer to “Checking, Cancelling or Correcting the Timer Programming Information” on page 40.

9 Press [ ON / STANDBY] to set a timer programming.

Timer Programming

0:00 THU 06/12

Date	Start	End	CH	STTL
				PDC
06/12	7:00	9:00	18
07/12	9:00	9:30	190
07/12	17:00	18:00	901
		New Program

1/1

The icon will appear on the front panel display and the unit enters to the timer-standby mode.

Note

•If you have not set the clock, the clock setting window will appear instead of the Timer Programming list. Continue from step 4 in “Manual Clock Setting” on page 31 before programming the timer.

•Press [L / P] to move the cursor in the Timer Programming list.

•Cancel the timer-standby mode by pressing

[ ON / STANDBY] before operation. When finished operating, press [ ON / STANDBY] to resume the timer-standby mode.

EN 39

Introduction Connections Basic Setup Recording

Playback

Editing Function Setup Others