REMOTE CONTROL
1 POWER
4. SLEEP Button - To set the TV to turn off after a preset |
amount of time, press the SLEEP button on the remote |
control. The clock will count down 10 minutes each time |
the button is pressed in the order of 120, 110, 100, ······ 20, |
10, 0. After the sleep time is programmed, the display will |
2
1 2 3
4 5 6
disappear then reappear momentarily every ten minutes to |
remind you the sleep timer function is operating. To |
confirm the sleep time setting, press the SLEEP button |
once and the remaining time will be momentarily displayed. |
3 | 7 | 8 | 9 | 10 |
0 |
|
|
| |
| CH RTN | RECALL |
| |
4 | SLEEP | CH + | MUTE | 11 |
|
|
|
| |
5 |
|
|
|
|
| To cancel sleep time, press the SLEEP button repeatedly |
| until the display turns to 0. |
5. | VOL (VOLUME) + / – Buttons - Press the + button to |
| increase or the – button to decrease the volume level. |
6. | MENU Button - Press to display the |
| function. |
7. | SET + / – Buttons - Press to select the desired setting |
| VOL |
| – |
| MENU |
6 | CH – |
– SET + | |
7 |
|
RESET
8 
TV/VIDEO CAP/TEXT
9 
VOL
+
ENTER
1/2
12
13
14
15
| during |
8. | RESET Button - Press to reset the |
| adjustments to their factory preset positions. |
9. | TV/VIDEO Button - Switches between the TV and external |
device inputs.
10. | RECALL Button - When you press this button, the |
| channel number will appear in the upper right corner of the |
| screen. Press the button again to remove it from the |
| screen. |
11. | MUTE Button - To turn off the sound, press this button |
| once. The TV will be silenced and the word “MUTE” will |
| appear on the screen. The muting feature can be released |
1.POWER Button - Press to turn on the TV. Press again to turn off the TV.
2.Direct Channel Selection Buttons
3.CH RTN Button - Repeatedly press CH RTN to toggle back and forth between the last two channels you tuned.
| by pressing the MUTE button again or one of the VOL + or |
| – buttons. |
12. | CH (CHANNEL) + / – Buttons - Press the + button to |
| change to a higher numbered channel set into memory. |
| Press the – button to change to a lower numbered channel |
| set into memory. |
13. | ENTER Button - Press to enter or select information for |
| |
14. 1/2 Button - Switches between channel 1 and channel 2 | |
in the closed caption mode.
15. CAP/TEXT Button - Press to switch between normal TV and the two closed caption modes (captions or text), when available.
Before using the remote control, batteries must first be installed.
HOW TO INSTALL BATTERIES
1. Open the battery compartment cover.
2. Install two “AAA” (penlight size) batteries.
3. Replace the battery compartment cover.
6
Use two “AAA” size penlight batteries (supplied) for the remote control. The batteries may last approximately one year depending on how much the remote control is used. For best performance, it is recommended that batteries should be replaced on a yearly basis, or when the remote operation becomes erratic.
Caution:
Never throw batteries into a fire.
Notes :
•Be sure to use AAA size batteries.
•Dispose of batteries in a designated disposal area.
•Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with applicable laws and regulations.
•If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones.
•When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.
•Always remove batteries from remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment.
6 | 12/26/05, 1:49 PM |