Onkyo DV-SP800 Setting the Video 1 Options, Component Video, Switching the S-Video Output Expert

Setting the Video 1 Options

■Component Video

Compared to a standard interlaced TV picture, a progressive scan TV is capable of stable, flicker-free images.

Set only if you connected the COMPONENT VIDEO OUT to a progressive-scan compatible TV or monitor.

Make changes to the [Component Video] settings in the setup screen [Video 1] menu.

Audio1 A2 Video1 V2 Language General

TV Screen	— 16:9(Wide)
Component Video	Progressive
Video Out	Video
S-Video Out	Interlace
Frame Search	— Off
Screen Saver	— Off
Move	SETUP Exit

•Progressive – Use this setting with TVs and monitors that have progressive scan component video inputs. Check the TV’s instruction manual if you are not sure about this.

•Interlace – (factory setting) use this setting with regular TVs that are not compatible with progressive scan. Check the TV’s instruction manual if you are not sure about this.

Notes

•This function only works when the color system recorded on the disc is NTSC.

•If this player is set to output progressive-scan video, it’s possible that the picture will appear stretched when playing discs recorded in 4:3 format. This happens when the TV’s aspect ratio is set [Full]. To see the picture in its correct aspect ratio, change the TV setting to [Normal].

•If your TV doesn’t have settings to change the aspect ratio of the picture, set this player to [16:9 (Compressed)].

•If you connect a TV that is not compatible with a progressive scan signal and choose one of the progressive scan settings, you will not be able to see any picture at all. With your TV connected using either the composite or S-Video terminals, choose the [Interlace] settings in the [Component Video] menu.

■Setting the Video Output Format for the AV CONNECTOR (European models only)

When connections are made to the AV CONNECTOR jack on the player via a SCART cable, it is possible to select the video format that is compatible with your TV or monitor. Select [Video] to have a composite video signal output, [S-Video] to have an S-video signal output, and [RGB] to have an RGB signal output. For more information on which format is most appropriate, refer to the instructions supplied with your TV or monitor. Make changes to the [Video Out] setting in the Setup screen [Video 1] menu.

Audio1 A2 Video1 V2 Language General

TV Screen	— 16:9(Wide)
Component Video		Interlace
Video Out		Video
S-Video Out		S-Video
Frame Search	— RGB
Screen Saver		Off
Move		SETUP Exit

Settings: Video (Factory setting)

S-Video

RGB

■Switching the S-Video Output Expert

You can switch the kind of S-Video signal output from the S-Video outputs. If you connected your TV with an S-Video cord, in rare cases the TV picture may appear stretched. In this case switch the output from [S2] to [S1].

Make changes in the [S-Video Out] in the Setup screen [Video 1] menu in the [Expert] menu mode (page 47).

Audio1 A2 Video1 V2 Language General

TV Screen	— 16:9(Wide)
Component Video	— Interlaced
Video Out	— Video
S-Video Out		S1
Frame Search	— S2
Screen Saver		Off
Move		SETUP Exit

Settings: S1

S2 (Factory Setting)

■Turning the Screen Saver On and Off Expert

As a protective function against residual images on the TV screen or monitor, a phenomenon referred to as “screen burn”, the screen saver appears when the same screen has been displayed for a length of time. By default, the screen saver is turned on. However, the screen saver function can be turned on and off at your discretion.

Make changes to the [Screen Saver] setting in the Setup screen [Video 1] menu in the [Expert] menu mode (page 47).

Audio1	A2	Video1 V2		Language	General
			TV Screen	— 16:9(Wide)
	Component Video			— Interlaced
			Video Out	— Video
		S-Video Out		— S2
		Frame Search		Off
		Screen Saver		On
				Off
		Move			SETUP	Exit
Settings:			On (Factory setting)
			Off
Note

Pressing 8 (or £ ) displays a playback screen, and pressing 8 (or £ ) again resumes playback.

■Frame Search Expert

Set this to [On] if you want to be able to do frame-accurate searching of DVD discs. On the default setting, the time & frame search is not available.

Audio1 A2 Video1 V2 Language General

TV Screen	— 16:9(Wide)
Component Video	— Interlace
Video Out	— Video
S-Video Out	— S2
Frame Search	On
Screen Saver	Off
Move	SETUP Exit

Settings: On

Off (Factory setting)

53