Onkyo CP702 instruction manual Troubleshooting

Page 46

Troubleshooting—Continued

Symptom

Possible cause

Remedy

 

 

 

The message “NO

 

 

PLAY” appears on the

The disc is dirty.

Remove the disc and clean it (page 8).

display?

 

 

 

 

 

Buttons on the DV-

Power supply voltage fluctuations and other

Turn off the DV-CP702, wait five seconds, then

turn it on again. If that doesn’t resolve the issue,

CP702 and remote con-

anomalies, such as static electricity, can

disconnect the power cord from the wall outlet,

troller don’t work?

interfere with normal operation.

wait five seconds, reconnect it, then try again.

 

 

 

 

 

 

There are no batteries in the remote

Install new batteries (page 15).

 

controller.

 

 

 

 

 

 

The batteries are flat.

Replace with new batteries (page 15).

 

 

 

 

The batteries are installed incorrectly.

Check the batteries and correct as necessary

 

(page 15).

 

 

 

 

 

 

You’re not pointing the remote controller at

Point the remote controller at the DV-CP702’s

Buttons on the DV-

the DV-CP702’s remote sensor.

remote sensor (page 15).

CP702 work OK but

 

 

 

Use the remote controller closer to the DV-CP702

those on the remote con-

 

You’re too far away from the DV-CP702.

(page 15). The remote controller has a range of

troller don’t?

 

approximately 16 ft. (5 meters).

 

 

 

 

 

 

A strong light source is interfering with the

Make sure that the DV-CP702 is not subjected to

 

direct sunshine or inverter-type fluorescent lights.

 

DV-CP702’s remote sensor.

 

Relocate if necessary.

 

 

 

 

 

 

If the DV-CP702 is installed in a cabinet

 

 

with colored glass doors, the remote control-

Open the doors, or use a cabinet without colored

 

ler may not work reliably when the doors are

glass.

 

closed.

 

 

 

 

Abnormal Behavior

The DV-CP702 contains a microcomputer for signal processing and control functions. In very rare situations, severe interfer- ence, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this should happen, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again. Alternatively, press and hold the STOP [] button until “RESET” appears on the display (about 10 seconds).

Restoring the Default Settings

To reset the DV-CP702 to its factory defaults, turn it on and, while holding down the STOP [] button, press the [STANDBY/ ON] button. “INITIALIZE” appears on the display. When the reset is complete, “COMPLETE” is displayed, and the DV- CP702 enters Standby mode.

46

Image 46
Contents DV-CP702 Contents Important Safety Instructions For models having a power cord with a polarized plug PrecautionsSur les modèles dont la fiche est polarisée Installing this Unit WarrantyPower Region NumbersDV-CP702 Features Supplied AccessoriesIntroduction Introduction Disc Notes Unsupported DVD FeaturesDisc Content Organization DVD Region Numbers Supported DiscsVideo CDs Cleaning DiscsIntroduction MP3/WMA/JPEG CompatibilityStoring Discs DV-CP702-related TerminologyCopyright Controls & Connectors Front PanelControls & Connectors Display Controls & Connectors Rear Panel Power cordControls & Connectors Remote Controller Controls & Connectors Accordance with the polarity diagram inside Before Using the DV-CP702Open the battery compartment, as shown Battery compartment Close the battery compartmentBefore Making Any Connections Connecting the DV-CP702AV Cables & Connectors Optical Digital InputsConnecting the DV-CP702 Connecting Your TV or Projector TV or projectorAnalog Connection Connecting the DV-CP702 Connecting Your Hi-Fi AmpConnecting for Dolby Digital or DTS Digital ConnectionWith Remote Interactive you can control your DV Connecting -compatible AV ComponentsConnection Diagram Use the following special functionsPowering Up the DV-CP702 Powering Up & Setting Up the DV-CP702First Time Setup Loading & Removing Discs Basic PlaybackLoading Discs During Playback Basic Playback Starting, Pausing & Stopping PlaybackSelecting Discs Basic Playback Load and select a DVD-Video disc Navigating Disc MenusOr Video CD Use the number buttons to specify a chapter or title Selecting Titles & Chapters by NumberPress the Search button Using the Disc Navigator Playlist appears in place of the file information Basic Playback Memory Playback in the Disc NavigatorWith the Disc Navigator open, press the Memory button To start memory playback, pressSelecting Tracks by Number Fast Forward & ReverseSlow-motion Playback Adjusting the Display BrightnessFrame-by-Frame Playback Using Jpeg CDs Using Chain ModeLocating Specific Points in Time Advanced PlaybackRepeat Playback Advanced Playback Random PlaybackMemory Playback Selecting Camera Angles Selecting Languages & Audio Formats Using Progressive ScanningSelecting Subtitles Using Last Memory During playback, press the DIS To cancel the information displayAdvanced Playback Displaying Information Press the Display button againMenu Setting Description Picture Configuring the DV-CP702Picture Menu Using the Onscreen Setup MenusTV Shape Progressive Setting Interlaced SettingPAL Output Setting Australian model only Digital Out Configuring the DV-CP702 Audio MenuLanguage Menu Dynamic Range Control Dolby Digital onlyDisplay Menu Pause/Still Operation Setting MenuScreen Saver Parental LockAuto Power Off Language Code ListInitial Setup Menu Selecting Other LanguagesTroubleshooting Troubleshooting Specifications Component VideoOnkyo U.S.A. Corporation Page Page Page