Onkyo DV-L55 instruction manual Troubleshooting

DV-L55_En.book Page 50 Friday, May 28, 2004 12:02 PM

Troubleshooting

If you have any trouble using your DV-L55, check the following table for possible causes and remedies. If you still can’t resolve the issue yourself, please contact your Onkyo dealer.

DVD Player

Symptoms	Causes		Remedies
	The power cord is not connected.	Connect the power cord to a suitable wall outlet
		(page 22).
Can’t turn on the
		Turn off the DV-L55, wait five seconds, then try
DV-L55?	External interference is affecting the	turning it on again. If that fails, disconnect the
	DV-L55’s digital circuitry.	power cord from the wall outlet, wait five seconds,
		reconnect it, then try turning it on again.
The disc tray won’t	The disc is not centered in the disc tray.	Place the disc in the center of the disc tray
		(page 25).
close properly?
	The disc is dirty.	Remove the disc and clean it (page 9).
	No disc is loaded.	Load a disc (page 25).
	The disc cannot be played because it’s	Use only compatible discs (page 7).
	incompatible.
	The disc is upside down.	Load the disc the correct way up (page 25).
	The disc is not centered in the disc tray.	Place the disc in the center of the disc tray
		(page 25).
Can’t start playback?
	The disc is dirty.	Remove the disc and clean it (page 9).
	The disc uses parental lock and the Paren-	Turn off the Parental Lock function (page 43).
	tal Lock function is on.
	The DVD-Video disc is intended for use	If the disc’s region number does not match the
		region number printed on the rear panel of the
	in another region.
		DV-L55, the disc cannot be played (page 46).
The picture distorts	The disc is dirty.	Remove the disc and clean it (page 9).
	You’re using the Fast Forward or Fast	A little picture distortion may occur when using
occasionally?
	Reverse function.	these functions. This is normal.
	The DV-L55 is connected to your TV via
Picture instability or	a VCR or other video equipment and a	Connect the DV-L55 directly to your TV
noise?	copy-protection system is affecting the	(page 17).
	picture.
	The wrong input source is selected on	On your TV, select the input to which the DV-L55
	your TV.	is connected.
	The video cable is not connected properly.	Check the video cable and correct as necessary
		(page 17).
No picture?
		No video is output by the S-Video and composite
	The video output is set to progressive	video outputs while progressive scanning is
	scanning.	selected. If your TV doesn’t support progressive
		scanning, select interlaced (page 18).
	If there’s a power failure, or the power	Before you disconnect the power cord, set the
		DV-L55 to Standby by pressing the [STANDBY/
Settings are not saved?	cord is disconnected inadvertently, any
		ON] button, and wait until “GOOD BYE” has dis-
	settings are lost.
		appeared from the display.
	The DV-L55 is connected to your TV via
	a VCR or other video equipment and a	Connect the DV-L55 directly to your TV
	copy-protection system is affecting the	(page 17).
Brightness is unstable	picture.
		If you select progressive scanning while
or the picture is noisy?
		using a TV that does not support it.
	Your TV doesn’t support progressive
		Switch the player to standby then, using the front
	scanning.
		panel controls, press STANDBY/ON while press-
		ing	to switch the player back to Interlace.
Chapters or tracks don’t	You are using repeat playback, program
play in the correct		Select normal playback (pages 32–34).
	playback, or random playback.
order?

50