Onkyo BD-SP807 Special Settings, Setting the BD Audio Mode, Adjusting the Picture

SPECIAL SETTINGS

Setting the BD Audio Mode

BD-V

There are 2 ways to set “BD Audio Mode” setting; whether to output the secondary and interactive audio accompanied by the primary audio or only the primary audio. Depending on the setting of the mode, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, or DTS-HD output changes between multi LPCM and bitstream.

1In stop mode with BD inserted, press [MODE].

2Use [K / L] to select your desired setting.

BD Audio Mode Mix Audio Output

“Mix Audio Output”:

If it is available, BD-video’s secondary and interactive audio will be output with the primary audio.

•The secondary audio is the audio for the secondary video (Director’s comment etc.) and the interactive audio is the audio for the interactive application (Button click sounds etc.).

“HD Audio Output”:

Only the primary audio will be output. Set this mode in order to output Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD audio of BD through HDMI connection.

3Press [RETURN] to exit.

•You can also set “BD Audio Mode” from the setup menu. Refer to page 38.

Note

•In “Mix Audio Output” mode, if there is no secondary and interactive audio, the audio will be output as “HD Audio Output” mode.

•In “Mix Audio Output” mode, even if you set “HDMI Multi(Normal)” in “HDMI Audio Out” setting, multi LPCM will be output from HDMI OUT jack for BD audio. Refer to page 14.

•In “Mix Audio Output” mode with HDMI audio being output, 2-channel down-mixed LPCM will be output from AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL) jacks for BD audio.

•In “Mix Audio Output” mode with “HDMI Audio Out” setting set to “Audio Mute” and “Digital Out”setting set to “Bitstream”, DTS, DTS-HD and LPCM will be output as Dolby Digital for BD audio. Refer to pages 14, 17.

•You can also set “ BD Audio Mode” setting from the setup menu. Refer to page 38.

Adjusting the Picture

BD-VDVD-V AVCHD

You can adjust the picture quality and store the setting you have adjusted on memory 1-5.

1During playback, press [MODE] repeatedly until the picture adjustment menu appears.

Memory1

32

2Use [K / L] to select a memory from “Memory 1” to “Memory 5” to store your setting, then press [ENTER].

3Use [K / L] to select a item to be adjusted, then use [{ / B] or [ENTER] to adjust the setting.

	2. Brightness			0
	1. Contrast			s +1 B
	7. Noise Reduction			Off
	item	Description		adjustment range
		Adjusts the
		difference
1. Contrast		between the	-7 to +7(0*)
		bright and dark
		parts of the
		picture.
		Adjusts the
2. Brightness		brightness of the	0 to +15(0*)
		picture.
		Adjusts the sharp-
3. Sharpness		ness of the picture	-6 to +6(0*)
		for
		frequency range.
		Detailed
4. Gamma		adjustment of the	0 to +5(0*)
Correction		picture’s bright-
		ness.
		Adjusts the bal-
5. Color		ance between	-7 to +7(0*)
		green and red.
			On*:Makes the dark parts
6. Black Level*1		Adjusts the black		brighter.
		level.	Off :Shows the original
				picture as recorded.
			Off*
			1	:Executes 3D noise
				reduction which
				detects and deletes
				the noise by compar-
7. Noise				ing each picture
		Reduces the noise		frames.
Reduction
			2	:Executes MPEG noise
(Not		of the		reduction which
available for		playback picture.
				reduces the block
BD/AVCHD)
				noise and mosquito
				noise on the subtitle
				on movie.
			3	:Executes both MPEG
				noise reduction and
				3D noise reduction.

* Default setting

*1 Not effective for the video signal of VIDEO OUT (COMPONENT) jacks (480i) and HDMI OUT jack.

Note

•The setting remains even you turn the unit into the standby mode except unplug the AC cord.

•For the picture output from HDMI OUT jack, “Black Level” is not effective.

•Adjusting the picture is effective for HDMI OUT jack, VIDEO OUTPUT (COMPONENT) jacks, AUDIO OUTPUT (DIGITAL OPTICAL / COAXIAL) jacks and VIDEO OUTPUT (VIDEO) jacks.

EN