NAD T524 owner manual To Turn on Progressive Scan, TV Output Select, Audio

Page 14

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS SVENSKA

Installation and Setup

BEFORE OPERATION

PROGRESSIVE SCAN

Progressive Scan Video provides the highest quality pictures with less flickering.

If you are using the Component Video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set Progressive Scan to On.

TO TURN ON PROGRESSIVE SCAN:

Connect Component out of the DVD to the input of your monitor/television, set your television or monitor to Component Input.

1Select “Progressive Scan” on the DISPLAY menu then press .

DISPLAY

TV Aspect

 

Display Mode

 

Progressive Scan

On

TV Output Select

Off

Prev.

Move

Enter

2Select “On” using the buttons.

3Press ENTER to confirm your selection. The confirm menu will appear.

NOTE

If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the DVD Player.

4When the confirm menu appears on your screen Cancel is

highlighted as default. Use the buttons to highlight Enter.

5Pressing ENTER will set the player to Progressive scan mode.

CAUTION

Once the setting for progressive scan output is entered, an image will only be visible on a progressive scan compatible TV or monitor. If you set Progressive Scan to On in error, you must reset the unit. First, remove the disc in the DVD Player. Next, press STOP ( ) and hold it for five seconds before releasing it. The video output will be restored to the standard setting, and a picture will once again be visible on a conventional analogue TV or monitor.

TV OUTPUT SELECT

Set the player’s TV Output Select options according to the TV connection type.

YPbPr: When your TV is connected with the COMPONENT VIDEO OUT/PROGRESSIVE SCAN jacks on the DVD player.

RGB: When your TV is connected with the SCART (RGB signal) jack.

AUDIO

Each DVD disc has a variety of audio output options. Set the player’s AUDIO options according to the type of audio system you use.

AUDIO

 

 

Dolby Digital

Bitstream

 

 

 

DTS

Bitstream

 

 

 

MPEG

PCM

 

 

 

 

 

 

Sample Freq.

48 kHz

 

 

 

5.1 Speaker Setup

Select

 

 

 

DRC

On

 

 

 

 

 

 

 

 

 

Move

Select

 

 

 

 

 

DOLBY DIGITAL / DTS / MPEG DVD DivX

BITSTREAM: Select “Bitstream” if you connect the DVD Player’s DIGITAL OUT jack to an amplifier or other equipment with a Dolby Digital, DTS or MPEG decoder.

PCM (FOR DOLBY DIGITAL / MPEG): Select when connected to a two-channel digital stereo amplifier. DVDs encoded in Dolby Digital or MPEG will be automatically downmixed to two-channel PCM audio.

OFF (FOR DTS): If you select “Off”, the DTS signal is not output through the DIGITAL OUT jack.

SAMPLE FREQ. (FREQUENCY) DVD-VDVD-A

If your receiver or amplifier is NOT capable of handling 96 kHz signals, select 48 kHz. When this choice is made, this unit automatically converts any 96 kHz signals to 48 kHz so your system can decode them.

If your receiver or amplifier is capable of handling 96 kHz signals, select 96 kHz. When this choice is made, this unit passes each type of signal through without any further processing.

Check the documentation for your amplifier to verify its capabilities.

5.1SPEAKER SETUP DVD-V DVD-A DivX

Select speaker settings, including volume balance and distance, or test the speaker settings.

Speaker settings are only active on the Analogue Multi-Channel Output. (See “Speaker Settings”, page 28.)

14

Image 14
Contents T524 Model no Serial no Date of Purchase Safety PrecautionsSerial Number Table of Contents Before USE Regional Code Types of Playable DiscsCm / 12 cm disc Mpeg DISC-RELATED Terms DVD ±R / DVD ±RWVCD Video CD MP3Front Panel and Display Window SCART/RGB OUT Rear PanelVideo OUT 12V TriggerRemote Control SearchDVD Player Connections Setting UP the PlayerConnections Progressive Scan Colorstream PROAudio Connection to Optional Equipment Digital MULTI-CHANNEL SoundPlayback STATUS/RESTRICTIONS Before OperationON-SCREEN Display ItemsTo Display and Exit the Menu Initial SettingsDisplay Mode DVD-VDVD-A General OperationTV Output Select Progressive ScanTo Turn on Progressive Scan AudioPBC VCD Dynamic Range Control DRCOthers Auto Play DVD-VRating DVD-V Password Security CodeLock Parental Control Country Code DVD-VOperation with DVD and Video CD DVD Video Discs Repeat CHAPTER/TITLE/OFF Still Picture and FRAME-BY-FRAME PlaybackRandom VCD Video CDS, Divx Discs Repeat TRACK/ALL/OFFTitle Menu DVD-VDVD-A Zoom DVD-V DVD-A VCD DivXPause DVD-V DVD-A VCD DivX Camera Angle DVD-VDVD-AViewing Another DVD Audio DiscsMoving to Another Group Audio CD Operation with Audio CD and MP3 / WMA DiscPlaying AN Audio CD or MP3/WMA Disc MP3 / WMARepeat TRACK/ALL/OFF CD MP3 WMA Audio CD and MP3 / WMA Disc Features Pause CDMoving to Another Track CD MP3 WMA Search CDRepeat Programmed Tracks Programmed PlaybackVideo CD Erasing a Track from Program ListOperation with Jpeg Disc Operation with a DVD VR Format Disc What is ‘CPRM’?Maintenance and Service Handling the UnitPlayable Codec formats Operation with a Divx Movie DiscPlayable DivX files Playable Audio formatAdditional Information Speaker Setup Troubleshooting Symptom Cause CorrectionTable of Languages and Their Codes Code LanguageCountry Code List Choose a country code from this listGeneral SpecificationsAccessories SystemManual C Version 12/04