Arcam DV135 manual Making audio connections, Scart output, Video, Composite video

Page 5

SCART output

The SCART connector is common on European A/V equipment and provides a convenient connection method between your DVD player and display device, carrying both video and stereo audio.

If you are using a SCART connection and you do not wish to listen to the audio through your TV, then it is best to mute your TV’s speakers; muting the TV will prevent this audio being heard.

Note that the SCART output has a control signal that switches your TV to its SCART input when the DV135 is turned on. It will also signal to wide-screen TVs the correct aspect ratio (16:9 or 4:3), provided this feature is supported by the TV.

S-Video

The S-Video output (also known as S-VHS or Y/C) is commonly supported by display devices worldwide. Connect the S‑VIDEO output of the DVD player to the S‑Video input of the display device using an appropriate cable.

Composite video

If your display device offers only a composite input (sometimes labelled CVBS or just ‘video’), connect this to the COMPOSITE video output of the DVD player using a 75Ω phono cable suitable for video use. Note that a composite video connection gives the lowest-quality output; if your display device supports other video connection types, we advise that those are used instead.

Making audio connections

The DV135 offers a number of alternatives for connecting audio. The connection type to use depends on the rest of your system; chose the type most appropriate to your amplifier.

If you want to listen to audio through... ...we recommend the following:

<Your television

How you listen to audio through your TV depends on the inputs it has and your video connection:

<SCART: If you are using a SCART connection, this will carry stereo audio. No further connection is required.

<HDMI: If you are using an HDMI connection (not DVI), this will carry audio. No further connection is required.

<Stereo phono: (For use with a connection type other than SCART or HDMI.) If your TV has stereo phono inputs, follow the instructions below for a stereo amplifier.

<Your stereo amplifier

If you wish to listen to audio from your player through a stereo amplifier, then use the stereo analogue outputs (marked AUDIO OUT L and R). These outputs provide a stereo down-mix of the source material. The two pairs of outputs (marked 1 and 2) are connected internally, so you can connect either pair.

Using a pair of high quality phono cables, connect the L (left) and R (right) outputs to the CD input of your receiver.

<Your surround-sound receiver

Connect either the HDMI or one of the digital audio outputs (optical or coax) to the DVD input of your receiver.

Some high quality receivers (such as those by Arcam) switch HDMI video, but do not decode audio from HDMI. If this is the case, you’ll need to connect both HDMI digital out (for video), and optical or coax cables from the Digital audio out connectors (for audio), into your surround-sound receiver.

Listening to DVD-audio or SACD discs

The high quality of DVD-audio and SACD discs can be realised only by using analogue outputs. Using a conventional digital connection between your DVD player and surround-sound receiver will not allow you to hear these discs at their best, since the audio carried across the digital link when these discs are played is compromised (i.e. limited to a sample rate of 48K). This is true for all DVD players and is not a limitation of your DV135.

Connect the stereo analogue outputs to the CD input of your stereo amplifier or surround-sound receiver.

Note that SACD audio is not available as an output on the Digital audio out (optical or coax) connectors or the HDMI digital out interface.

English

DV135

E-5

Image 5
Contents DV135 Safety compliance Safety guidelinesImportant safety instructions Contents Making video connections InstallationPositioning the unit Scart output Making audio connectionsVideo Composite videoRemote-control and trigger inputs Inserting the batteries into the remote controlConnecting to a power supply Introduction Basic use of your DVD playerFront-panel controls Basic operationCR-515 remote control DV135 Advanced controls CR-515Using the Set-up menus Configuring your DVD playerObtaining a picture Set-up menuOperational set-up Video set-up Hdmi resolutionMain video output Display standardAnalogue Ntsc black Pedestal Analogue resolutionHdmi colour space Audio set-up VCD modeDigital audio output DVD sample rateBy setting these items to 0ms no delay Special playback modes DVD/VCD special playback modesJumping to a particular point Control window Disc navigator screenFile/Folder Troubleshooting Connecting using HdmiHdmi interface About HdmiPlayback control commands Power commandsDisplay control commands Advanced control commandsContinual improvement policy Technical specificationsDisc types supported Compressed audio compatibility CD-R/RW and DVD-R/RW compatibilityPicture disc compatibility PC created disc compatibilityOn line registration GuaranteePage Pembroke Avenue, Waterbeach, Cambridge CB25 9QR, England