Samsung DVD-V6400, DVD-V6000, DVD-V5450 user manual Immediately, Prog or

Page 29

Recording a Programme

 

Recording a Programme

Immediately

 

with Automatic Stop

 

 

 

Before recording a programme, you must have preset the corresponding station (unless you are recording via an external video source). If you have not done so, refer to pages 18~19.

1

Switch on the television.

 

 

 

 

 

Insert the video tape in to the VCR deck, with the

2 window visible and the safety tab intact or the

 

 

opening covered with adhesive tape. The DVD-

 

 

VCR is switched on automatically.

 

 

 

 

 

Select the station by pressing the PROG( or )

3 button or select the source (AV1, AV2(DVD-V5450/

 

 

DVD-V5500/DVD-V6400/ DVD-V6500), or

 

 

AUX(DVD-V5500/DVD-V6000/ DVD-V6500)) by

 

 

pressing the INPUT SEL. button for a satellite

 

 

tuner or external video source. The station number

 

 

is displayed and the programme can be seen on

 

 

the television.

 

 

 

4

Select the recording speed by pressing the

SPEED button as many times as required (refer to

 

 

page 28).

 

 

 

 

 

Hold down the REC (●) button for a while to start

5 recording.

 

 

The record indicator appears on the television and

 

 

DVD-VCR display. An index is recorded on the

 

 

tape (refer to page 39).

 

 

 

6

To stop recording, press the ■ button once.

• If your DVD-VCR ejects the cassette when you

start recording, check to make sure that the cassette’s safety tab is intact or that the opening (created by a broken safety tab) is overed with adhesive tape.

• If you reach the end of the tape while recording, the cassette rewinds automatically.

This function enables you to record up to nine hours (LP) of programmes.

Your DVD-VCR stops automatically after the requested length of time.

1

Switch on the television.

 

 

 

Insert the cassette on which the programme is to be

 

2 recorded, with the window visible and the safety tab

 

 

 

intact or the opening covered with adhesive tape.

 

 

 

The DVD-VCR is switched on automatically.

 

 

 

 

 

3

Select the station to be recorded by pressing the

 

PROG( or

) button or select the source (AV1,

 

 

 

AV2(DVD-V5450/VD-V5500/DVD-V6400/DVD-

 

 

 

V6500), or AUX(DVD-V5500/ DVD-V6000/ DVD-

 

 

 

V6500)) by pressing the INPUT SEL. button for a

 

 

 

satellite tuner or external video source.

 

 

 

The station number is displayed and the

VCR

 

 

programme can be seen on the television.

 

 

 

 

 

 

Functions

 

 

Select the recording speed by pressing the SPEED

5 recording.

 

4 button as many times as required (refer to page 28).

 

Hold down the REC (●) button for a while to start

The record indicator appears on the television screen and DVD-VCR display. An index is recorded on the tape (refer to page 39).

6 Press the REC (●) button several times to increase the recording time in:

•30-minute intervals up to four hours

•1-hour intervals up to nine hours

The length is displayed on the television displays. The selected programme is recorded for the length of time requested. At the end of that time, the DVD-VCR stops recording automatically and power off.

LENGTH 2:30

SET LENGTH :

PRESS REC ●

7 If you wish to cancel the recording before the end, press the STANDBY/ON button.

•If the end of the tape is reached while recording, the recording stops and power off.

English - 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents DVD-V5450 DVD-V5500 DVD-V6000 DVD-V6400 DVD-V6500 Do not Open the DVD-VCR. Refer to service personnel Safety InstructionsCharacteristics Disc Type and CharacteristicsDisc Markings Play Region NumberContents Reference Overviews Rear View of the DVD-VCR DVD-V6000 Display IndicatorsAccessories Clear Tour of the Remote ControlQuick Overview ConnectionsConnecting the Audio Output Cable AV1EURO AV By means of 21-pin Scart CableBy means of RF Cable AV2 in By means of 21-pin Scart CableDVD Use the S-Video connection method only forComponent Video OUT jacks on the rear Progressive ScanDVD-V6000/DVD-V6500 Plug & Auto Setup Settings Time Setting the Clock AutomaticallyPress the œ or √ button to select Auto Clock Press the … or † button to select OnPress the OK or √ button again Setting the MenuLanguage Automatically TV Station Table menu is displayed Station name is set automatically from Broadcast signalPress the … or † button to select Name Setup, then press the OK or √ button Clearing a Preset StationTV Station Table menu is displayed Press the … or † button to Select ManualNumber assigned to a station Setting the VCR Output ChannelPress the OK button to change the programme VCR Selecting the Colour ModePress the OK or √ button ControlPress the … or † button to select User Set, then Extend Auto Power offOff 10 20 30 40 50 Off 1 Hour 2 Hour 3 HourType Screen MessagesPress the … or † button to select Screen MessagesTape Select is highlighted Repeat Play Selecting Recording SpeedPress the OK or √ button Prog or ImmediatelyEdit Function VideoPlus code Using the VideoPlus Feature DVD-V6000/DVD-V6400/ DVD-V6500DVD-V6400 Select an input Press the œ or √ button to select PRDVD-V6500 or V6000/DVD-V6500 Changing any other valuePress the √ button to select Day, then press the … Timer programming menu is displayedOr † button to select the required day DLYAuto Tape Speed Select TimeSpeed Corresponding information Checking a Preset RecordingPress the … or † button to select the programme To be cancelled, then press the Clear buttonPlaying a Cassette Adjusting PictureIllustration Option DescriptionMIX Mono L R Go To 00000 Stop Searching for a Specific SequenceEnd Search Press the … or † button to select End SearchIndex Skip Search Intro ScanŒœ or √√ button Using the Tape CounterSequence Using the Disc Menu Language Setting Up Language FeaturesUsing the Subtitle Language Using the Audio LanguageDolby Digital Out OptionsMPEG-2 Digital Out Dynamic CompressionTV Aspect Setting Up the Display OptionsBlack Level Ntsc Disc OutputRe-enter Password menu is displayed to confirm the password Setting Up the Parental ControlPress the OK or √ button Use Password menu is displayed Setup menu is displayed DVD-VCR is lockedChanging the Password Setting up the Rating LevelRegistration DivX Feature TablePress the OK or √ button Message is displayed To DVD-VCRPlease do not change the file name How to make an update discUpdate procedure Special Playback Features When in VCD 2.0 Mode Menu ON, this Using the Display FunctionUse the œ or √ button to make the desired setup VCDDVD-V6400/DVD-V6500 CDRatio EZ View If you are using a 169 TVIf you are using a 43 TV VCDDVD-V6400/DVD-V6500, CD Selecting the Audio LanguageZoom Changing the Camera AngleDuring playback, press the Menu button Press the … or † button to select FUNC, thenMarks Cancel Chapper/TitleRepeat Chapter/Title Recalling a Maked SceneTo B Repeat Cancel A-B RepeatMP3/WMA Play Function MP3/WMA PlayRepeat CD-R MP3/WMA discsPress the …/†,œ/√ buttons to select the first track Program PlayRamdom Play Zoom Album ModeRotation CD-R Jpeg Discs Slide showWhen the disc is inserted, the file structure Playback FeaturesDisc will be shown. Depending on the file Format, a different icon will appear next to eachZoom Reference General Technical SpecificationsInput OutputPermanently damage the video heads Troubleshooting Guide VCRProblem Solution Troubleshooting Guide DVD United Kingdom Republic of Ireland This Appliance is Distributed by Electronics
Top Page Image Contents