Samsung CL-21Z30 manual Connecting a Camcorder, Connecting to an Analog Amplifier

Page 17

I N S TA L L AT I O N

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a Camcorder to your TV. They allow you to view the Camcorder tapes without using a VCR.

•Please be sure to match the color coded input terminals and cable jacks.

1

Locate the A/V output jacks on the Camcorder. They are usually found on the side or rear of the Camcorder.

2

Connect a set of audio cables between the “AV IN 2 (L, R)” jacks on the TV and the AUDIO OUT jacks on the Camcorder.

If you have mono Camcorder, connect L(mono) to Camcorder audio out using only one audio cable.

3	3
Connect a video cable between the “AV IN 2 (VIDEO)” jack on

the TV and the VIDEO OUT jacks on the Camcorder.

The audio-video cables shown here are usually included with a

Camcorder. (If not, check your local electronics store.) If your

Camcorder is stereo, you need to connect a set of two cables.

2

Connecting to an Analog Amplifier

•Please be sure to match the color coded input terminals and cable jacks.

The “AV OUT (L, R)” jacks cannot be used for external speakers. You must hook them up to an amplifier.

When an audio amplifier is connected to the “AV OUT (L, R)” jacks: Decrease the gain (volume) of the TV, and adjust the volume level with the Amplifier's volume control.

English - 17

Image 17

Contents Owner’s Instructions English Operation InstallationYour New TV Appendix Special FeaturesTroubleshooting Accessories List of FeaturesIndicator ¨ Remote Control SensorFamiliarizing Yourself with the TV Control ButtonsAudio Input Connection Jacks Side´ Video Input HeadphoneAudio-Video Output jacks ¨ Component Video Input Connection Jacks RearJacks Y, P B, P R ´ Video Input jacks´ Number buttons Remote Control+100 VOL +, VOLInstalling Batteries in the Remote Control Antennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasSeparate VHF and UHF Antennas Antennas with 75-ohm Round LeadsCable without a Cable Box Connecting Cable TVConnecting to a Cable Box that Descrambles All Channels Connecting to a Cable Box that Descrambles Some Channels Connecting a Second VCR to Record from the TV Connecting a VCRConnecting to Regular Audio and Video Jacks Connecting a DVD PlayerConnecting to Y, PB, PR Connecting to an Analog Amplifier Connecting a CamcorderConnect a video cable between the AV in 2 Video jack on TV and the Video OUT jacks on the CamcorderPress the Power button on the remote control Plug & Play FeatureTurning the TV On and Off Start Plug & Play is displayedPress the Enter button to start When you have finished Press the Menu buttonPress the Enter button to stop Enjoy yourViewing the Menus and On-Screen Displays Press the Info button on the remote controlViewing the Menus Viewing the DisplaySelecting a Menu Language Memorizing the Channels Selecting the Video Signal SourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Using the Number Buttons Using the Channel ButtonsUsing the PRE-CH Button to Select the Previous Channel Changing ChannelsLabelling the Channels You cannot select Name in the AV modePress the Enter button again Using Automatic Picture SettingsPicture Control Customizing the Picture Resetting the Picture Settings to the Factory Defaults Sound Control Adjusting the VolumeUsing the Mute Button Using Automatic Sound Settings Select the balance or a Customizing the SoundSelect Equalizer, then Press the Enter button Clock Setting the ClockSetting the Signal Source Viewing an External Signal SourcePress the Enter button Press the Exit button to exit Assigning Names to External Input ModeChapter Four Fine Tuning ChannelsLNA Low Noise Amplifier depending on the model Digital Noise Reduction Press the … or † button to select Tilt Tilt depending on the modelDNIe Jr Press the Enter button to select PIP Viewing Picture-In-Picture depending on the modelActivating the PIP Changing the Size of the Sub Picture Selecting an External SourceSwapping the Sub Picture and Main Picture Changing the Channel of the Sub Picture Changing the Position of the Sub PictureUsing the R.Surf Feature Choosing a Multi-Channel Sound MTS track Auto Volume Set the Off Timer as methods for On Timer setting Setting the On/Off TimerOn Timer Channel Setting the Preferred Channel and Volume LevelSetting the Sleep Timer Press the Enter button to select Caption Viewing Closed Captions On-Screen Text MessageCaption Mode Channel Field Move Enter Return Press the œ or √ button to select the channel to be locked Locking the Channel depending on the modelSetting the Blue Screen Mode Setting the On/Off Melody Viewing the Demonstration Chapter Five Identifying ProblemsSpecifications Cleaning and Maintaining Your TVUsing Your TV in Another Country This page is intentionally Left blank This page is intentionally Left blank Country Customer Care Center Web Site Contact Samsung WORLD-WIDE