Samsung CL17M2MQ Connecting a VCR, Unplug the cable or Antenna from the back, Back of the VCR

Page 13

I N S TA L L AT I O N

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 9-12). Skip step 1 if you have not yet connected to an antenna or a cable system.

1

Unplug the cable or
antenna from the back of
the TV.	ANT IN

2	VCR Rear Panel
Connect the cable or
antenna to the	Incoming
ANTENNA IN terminal on	Incoming
ANTENNA IN terminal on	Cable or
the back of the VCR.	Antenna
3	VCR Rear Panel	TV Rear Panel
Connect a coaxial cable
between the ANTENNA
OUT terminal on the VCR
and the antenna
terminal on the TV.		Coaxial Cable

ANT IN

A coaxial cable is usually included with a VCR. (If not, check your local electronics store).

4

Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO jacks on the TV.

5

Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack on the TV.

VCR Rear Panel	TV Rear Panel

Audio Cable

VCR Rear Panel	TV Rear Panel
VCR Rear Panel
	Video Cable

ANT IN

ANT IN

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Note: This figure shows the Standard connector-jack panel. The actual configuration for your TV may be different.

13

Image 13

Contents Owner’s Instructions Your New TV InstallationOperation Troubleshooting Special FeaturesAppendix Chapter One List of Features« VOL , + Stand by indicator Remote Control SensorPower CH and CH Familiarizing Yourself with The TVDevices For private listening Side Panel JacksDevices Connect video from a DVD player Rear Panel JacksMode « Number buttons Remote Control+100 VOL -, VOL +Antennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasAntennas with 75-ohm Round Leads Connecting Cable TVSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles Some Channels Connecting to a Cable Box that Descrambles All ChannelsConnect this cable to a two-way splitter Cable Box Unplug the cable or Antenna from the back Connecting a VCRConnect the cable or Antenna to Antenna in terminal onConnect a set of audio Connecting a DVD Player 480i OptionConnecting a Camcorder Installing Batteries in the Remote Control Turning the TV On and Off Press the Power button on the remote controlViewing the Menus and On-Screen Displays Viewing the MenusPress the Menu button to display the menu Selecting a Menu LanguagePress the Exit button to exit Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method Directly Accessing Channels Using the Channel ButtonsUsing the PRE-CH Button to select the Previous Channel Changing ChannelsPress the Menu button to display menu Customizing the PictureUsing Automatic Picture Settings Using Mute Adjusting the VolumeCustomizing the Sound Press the ˇ or ˆ button Using Automatic Sound SettingsTo increase or decrease the value of a particular item Press the Menu button to display the on-screen menu Setting the ClockSimply press Viewing a VCR or Camcorder TapePress the ˇ and ˆ but- tons to adjust the fine tun- ing Fine Tuning ChannelsPress the or button to select Color Tone Selecting the Color ToneChanging the Screen Size Screen display will read Surf off Using the Surf FeaturePress the or button to select MTS Choosing a Multi-Channel Sound MTS SoundtrackAuto Volume Extra Sound SettingsPM appears to the right of the hour Setting the On/Off TimerSetting the Sleep Timer Viewing Closed Captions Chapter Five Identifying ProblemsUsing Your TV in Another Country Cleaning and Maintaining Your TVSpecifications