Samsung CL17M2MQ manual Connecting to a Cable Box that Descrambles All Channels

Page 11

I N S TA L L AT I O N

Connecting to a Cable Box that Descrambles All Channels

1

Find the cable that is con- nected to the ANTENNA OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

2

Connect the other end of this cable to the VHF/UHF antenna terminal on the back of the TV.

ANT IN

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of coaxial cable. (These items are available at most electronics stores.)

1

Find and disconnect the cable that is connected to the ANTENNA IN terminal on your cable box.

This terminal might be labeled

“ANT IN”, “VHF IN” or simply, “IN”.

2

Connect this cable to a two-way splitter.

Incoming Cable

Splitter

3

Connect a coaxial cable between an OUTPUT ter- minal on the splitter and the IN terminal on the cable box.

Incoming Cable

Splitter

Cable Box

4

Connect a coaxial cable between the ANTENNA OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

Incoming

Cable

Splitter

 

 

 

RF (A/B)

 

 

 

 

 

 

Cable Box

 

Switch

 

 

 

 

 

 

 

Continued...

11

Image 11
Contents Owner’s Instructions Operation InstallationYour New TV Appendix Special FeaturesTroubleshooting Chapter One List of FeaturesFamiliarizing Yourself with The TV Remote Control Sensor« VOL , + Stand by indicator Power CH and CHDevices Side Panel JacksDevices For private listening Mode Rear Panel JacksConnect video from a DVD player VOL -, VOL + Remote Control« Number buttons +100Antennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVAntennas with 75-ohm Round Leads Separate VHF and UHF AntennasConnect this cable to a two-way splitter Connecting to a Cable Box that Descrambles All ChannelsConnecting to a Cable Box that Descrambles Some Channels Cable Box Antenna in terminal on Connecting a VCRUnplug the cable or Antenna from the back Connect the cable or Antenna toConnect a set of audio Connecting a DVD Player 480i OptionConnecting a Camcorder Installing Batteries in the Remote Control Viewing the Menus Press the Power button on the remote controlTurning the TV On and Off Viewing the Menus and On-Screen DisplaysPress the Exit button to exit Selecting a Menu LanguagePress the Menu button to display the menu Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method Changing Channels Using the Channel ButtonsDirectly Accessing Channels Using the PRE-CH Button to select the Previous ChannelPress the Menu button to display menu Customizing the PictureUsing Automatic Picture Settings Customizing the Sound Adjusting the VolumeUsing Mute To increase or decrease the value of a particular item Using Automatic Sound SettingsPress the ˇ or ˆ button Press the Menu button to display the on-screen menu Setting the ClockSimply press Viewing a VCR or Camcorder TapePress the ˇ and ˆ but- tons to adjust the fine tun- ing Fine Tuning ChannelsPress the or button to select Color Tone Selecting the Color ToneChanging the Screen Size Screen display will read Surf off Using the Surf FeaturePress the or button to select MTS Choosing a Multi-Channel Sound MTS SoundtrackAuto Volume Extra Sound SettingsPM appears to the right of the hour Setting the On/Off TimerSetting the Sleep Timer Viewing Closed Captions Chapter Five Identifying ProblemsSpecifications Cleaning and Maintaining Your TVUsing Your TV in Another Country