Samsung PCK 6115R Viewing a VCR or Camcorder Tape, Video1 Video2 Video3, Press TV/VIDEO to exit

Page 36

O P E R AT I O N

Viewing a VCR or Camcorder Tape

You must select the appropriate mode in order to view the VCR or Camcorder signal on the TV.

1

Make sure that the remote control is controlling the TV set. (Press the MODE button and make sure that the “TV” LED is illuminated.)

2

Press TV/VIDEO on the remote control, and the following on- screen menu will appear:

TV/Video Menu

ANT/CATV

Video1

Video2

Video3

S-Video1

S-Video2

DVD

3

Use the CH▲ or CH▼ button to highlight a particular signal source, and then press VOL+ to activate it.

Press TV/VIDEO to exit.

When you press the TV/Video button, the on-screen display identifies all the active video sources (and their corresponding input jacks):

3.14 CHAPTER THREE: TV OPERATION

Page 35 Page 37
Image 36
Page 35 Page 37
Contents
Owner’s Instructions Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding FCC Information Installation Your New TVOperation Special Features TroubleshootingList of Features Chapter OneFamiliarizing Yourself with The TV Front Panel Jacks Super Video in jack Audio in jacks´ Video in jack Rear Panel Jacks Super VideoAudio Inputs Connect to an antenna or to a cable TV systemPIP Number buttons+100 ˝ CH and CH Channel Up/DownRemote Control ¸ VCR controls For model PCJ533RF PIP ControlsFor model PCJ532RF/PCJ534RF PCK6115ROtherwise, the picture may Flicker Connecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsConnecting Cable TV Antennas with 75-ohm Round LeadsSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles All Channels Connecting to a Cable Box that Descrambles Some ChannelsConnect this cable to a two-way splitter Connecting a VCR Unplug the cable or antenna from the back of the TVConnecting an S-VHS VCR Antenna or cable to your VCR and your TVConnecting a Digital TV Set-Top Box Connecting a Second VCR to Record from the TVConnecting a Camcorder Installing Batteries in the Remote Control Adjusting Basic Convergence Press PowerTurning the TV On and Off Adjust Red Convergence To do Left or Right ConvergenceWith the power on, press Menu Viewing the Menus and On-Screen DisplaysViewing the Menus Viewing the DisplaySelecting a Menu Language Selecting the Video Signal-source Press CH two times to highlight SET UP Press VOL +Memorizing the Channels Press MENU, then press CH twice to highlight SET UP Storing Channels in Memory Automatic MethodUsing the Channel Buttons Directly Accessing ChannelsChanging Channels Adding and Erasing Channels Manual MethodSetting the Clock Press the CH or CH button to select the correct minutesPress Menu three times to exit Adjusting the Volume Using MutePress VOL + or VOL to increase or decrease the volume Customizing the Picture Video icon will be highlighted starts blink- ingUsing Automatic Picture Settings Alternate methodCustomizing the Sound Press Menu to display the menuUsing Automatic Sound Settings Viewing a VCR or Camcorder Tape Video1 Video2 Video3Press TV/VIDEO to exit Customizing Your Remote Control Setting Up Your Remote Control to Operate Your VCRTurn off your VCR or Setting Up Your Remote Control to Operate Your Cable Box VCR Codes DVD CodesTurn off your cable box Cable Box CodesSetting the On/Off Timer Press CH or CH to select the appropriate minutesSetting the Sleep Timer When finished, pressPress the Sleep button on the remote control Viewing Closed Captions Press VOL+Press VOL+ to open Caption menu Fine Tuning Channels Select the appropriate channel Press MenuLNA Low Noise Amplifier Press CH twice to highlight LNASpecial Audio Options Dolby Surround, MTS, and Headphones Dolby PrologicDolby 3D Phonic Drama, Action, or TheaterChoosing a Multi-Channel Sound MTS Soundtrack Press CH to highlight MTSUsing Wireless Headphones Setting up Wireless Headphones with Picture-in-PictureViewing Picture-in-Picture Activating Picture-in-PicturePress VOL + to select PIP menu Press VOL + to select PIP OnSelecting a Signal Source Antenna or Cable for PIP Selecting a Signal Source External A/V for PIPSwapping the Contents of the PIP image and Main image Changing the PIP Channel Changing the Location Rotating the PIP WindowFreezing the PIP Image Changing the Size of the PIP WindowUsing the V-Chip Setting Up Your Personal ID Number PINPress CH six times to select the V-chip menu Press VOL+ How to Enable/Disable the V-Chip How to Set up Restrictions Using the TV guidelinesTV-Y Young children TV-Y7 Children 7 and over General audienceParental guidance TV-14E C I a L F E AT U R E S NC-17 Identifying Problems Chapter FiveCleaning and Maintaining Your TV Using Your TV in Another CountrySpecifications
Related manuals
Manual 58 pages 29.73 Kb