Samsung TXN 2022, TXN 1634F Connecting a VCR, Unplug the cable or antenna from the back of the TV

Page 18

I N S TA L L AT I O N

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 2.1-2.4). Skip step 1 if you have not yet connected to an antenna or a cable system.

1

Unplug the cable or antenna from the back of the TV.

2

Connect the cable or antenna to the ANTENNA IN terminal on the back of the VCR.

3

Connect a coaxial cable between the ANTENNA OUT terminal on the VCR and the antenna terminal on the TV.

A coaxial cable is usually included with a VCR. (If not, check your local electronics store).

4

Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO jacks on the TV.

5

Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack on the TV.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Note: This figure shows the Standard connector-jack panel. The actual configuration for your TV may be different.

2.5 CHAPTER TWO: INSTALLATION

Image 18

Contents Owner’s Riskofelectricshock Donotopen Thank You for Choosing Samsung Safety Read these instructions Installation Your New TVOperation Special Features TroubleshootingList of Features Chapter OneFamiliarizing Yourself with The TV Rear Panel Jacks DVD Video input jacks OptionVHF/UHF Antenna terminal ¨ +100 Remote ControlNumber buttons SleepSize ´ Number buttons+100 SETRemote Control ¯ VCR Controls ∙ F.F˘ PIP Controls Not available Connecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsSeparate VHF and UHF Antennas Connecting Cable TVAntennas with 75-ohm Round Leads Cable without a Cable BoxConnecting to a Cable Box that Descrambles All Channels Connecting to a Cable Box that Descrambles Some ChannelsConnect this cable to a two-way splitter S TA L L AT I O N Connecting a VCR Unplug the cable or antenna from the back of the TVConnecting a Camcorder Connecting a DVD Player OptionInstalling Batteries in the Remote Control Viewing the Menus and On-Screen Displays Press the Power button on the remote controlTurning the TV On and Off Viewing the MenusSelecting a Menu Language Selecting the Video Signal-source Memorizing the ChannelsANT antenna STD, HRC or IRC all cable TV Storing Channels in Memory Automatic Method Adding and Erasing Channels Manual Method Press the VOL+ or VOL- button to select Added or ErasedAdjusting the Volume Changing ChannelsSetting the Clock Or CH button repeat- edly until the correct hour appearsCustomizing the Picture Press the Menu button to display the menuUsing Automatic Picture Settings Using Automatic Sound Settings Viewing a VCR or Camcorder Tape Press the VOL+ or VOL- buttonPress the Menu button twice to exit Customizing Your Remote Control Setting Up Your Remote Control to Operate Your VCR or DVDTurn off your VCR or VCR Codes DVD Codes Setting Up Your Remote Control to Operate Your Cable Box Cable Box CodesFine Tuning Channels Changing the Screen Size Using the Surf Feature Setting the On/Off Timer Setting the Sleep Timer When finished, press the VOL + buttonPress the Sleep button on the remote control Sound Features Choosing a Multi-Channel Sound MTS SoundtrackExtra sound settings Turbo Sound, or Surround SurroundViewing Closed Captions Using the V-Chip Setting Up Your Personal ID Number PINPress the Menu button three times to exit How to Enable/Disable the V-Chip How to Set up Restrictions Using the TV guidelinesParental guidance TV-Y Young children TV-Y7 Children 7 and overGeneral audience TV-14E C I a L F E AT U R E S Repeatedly press the CH Button to select a General audience no restrictionsIdentifying Problems Chapter FiveCleaning and Maintaining Your TV Using Your TV in Another CountrySpecifications