Samsung HP-P5071 manual Memorizing the Channels, Selecting the Video Signal-source

Page 33

Memorizing the Channels

Your PDP can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the

CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the PDP (i.e., an antenna or a cable system).

Press the MENU button. Press the ▲ or ▼ button to

1 select “Channel”, then press the ENTER button.

2 Press the ENTER button to select “Air/CATV”.

Press the ▲ or ▼ button to select “Air”, “STD”,

3 “HRC” or “IRC”.

•If you are connected to an antenna, leave “Air” displayed. If you connected cable, press the

▲ or ▼ button to the display the type of cable system: “STD”, “HRC” or “IRC”.

(If you are not sure which type of cable system you have, contact your cable company).

4 Press the MENU button to exit.

TV		Channel

	Air/CATV	: Air				√
	Auto Program					√
	Add/Delete					√
	Fine Tune					√
	LNA	: On				√
	Scan					√
	Move	Enter		Return


TV		Channel
	Air/CATV	: Air		Air
	Auto Program
	Auto Program			STD
	Add/Delete			STD

				HRC
	Fine Tune			HRC

				IRC
	LNA	: On		IRC
	Scan
	Move	Enter		Return


TV		Channel
	Air/CATV	: Air		Air
	Auto Program
	Auto Program			STD
	Add/Delete			STD

				HRC
	Fine Tune			HRC

				IRC
	LNA	: On		IRC
	Scan
	Move	Enter		Return

Note

•STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (Next page).

33

Image 33

Contents Owner’s Instructions User Instructions WarrantyScreen Image retention Cell DefectTable of Contents Page General Information Remote Control Signal Receiver Power IndicatorSpeakers Source buttonPC Input RGB in / Audio Video Input Audio Input L, R Ferrite CoresVIDEO1, S-VIDEO2 AV1, AV2, AV3Remote Control Buttons Remote Control Operation Range ∑ Reset button¸ SRS Tsxt button ˛ MTS buttonInstallation Notes Wall Installation InstructionsWall Mount Bracket Support Bars ScrewsHow to assemble the Wall Mount Bracket Wall Installation Instructions Factory default How to Adjust Mounting AngleConnecting External Devices to the PDP Change AngleHow to Assemble the Speakers Standing Installing the SpeakersParts Speakers Speaker Dust CoverBlack How to Assemble the Speakers Wall Mount Black How to assemble the Stand-Base Connections Antennas with 75-ohm Round Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVPage Videotape Playback Connecting a VCRConnecting a Camcorder Viewing camcorder tapesViewing Tapes Connecting a DVD Player 480i, 480p Playing DVDTo Play DVD To Watch DTV Watching DTVOperation Turning the PDP On and Off Viewing the Menus and DisplaysViewing the Menus Displaying Status Information Press the Enter button to confirm your choice Plug & Play FeatureEnjoy your watching Plug and Play can only be accessed in the TV mode Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method To View Memorized Channels PIP Mode Adjusting the Volume Using MuteChanging Channels Setting Up Your Remote Control Remote Control Codes Setting the Signal Source Viewing an External Signal SourceAssigning Names to External input mode Page Picture Control PIP Customizing the PictureUsing Automatic Picture Settings Selecting the Color Tone DNIe Digital Natural Image engine Changing the Screen Size Panorama 169WideZoom 3NormalStill Freezing the PictureSelecting the PIP Screen Viewing the Picture-in-PictureSelecting an External Signal Swapping the Contents of the PIP and Main Image Changing the Size of the PIP Window Changing the Location of the PIP Image Selecting a Signal Source Antenna or Cable for PIP Changing the PIP Channel Setting the MCCMy Control Color Mode Emerald Green Indian Pink MCC Mode CharacteristicsMCC Custom Settings Resetting the MCC Colors to the Factory Defaults Page Sound Control Customizing the Sound Using Automatic Sound Settings Choosing a Multi-Channel Sound MTS Soundtrack Using the Auto Volume TruSurround XT, SRS and Symbol Setting the TruSurround XTListening to the Sound of the SubPIP Picture Selecting the Internal Mute Channel Control Fine Tuning Channels LNA Low Noise Amplifier Page Connecting a PC and Operation To watch the PC screen Connecting a PCPin Configuration Setting up Your PDP Plug and PlaySub Cable How to Set up Your PC Software Windows only IBM PC / AT Adjusting the R.G.B Adjusting the PC ScreenChanging the Position of the Image Picture Automatic Adjustment Picture Quality AdjustmentCoarse Adjustment Fine Tuning Fine Information Page Time Setting Setting the Clock Setting the Sleep Timer Setting the Timers Air Page Function Description Selecting a Menu Language Digital Noise Reduction Selecting the Film Mode Using the Color Weaknees Enhancement Option Setting the Melody Sound Setting the Blue Screen Selecting the Fan Viewing Closed Captions Setting Up Your Personal ID Number PIN Using the V-ChipHow to Enable/Disable the V-Chip How to Set up Restrictions using the TV guidelines 105 106 107 Page Appendix Problem Possible Solution TroubleshootingIdentifying Problems Care and MaintenanceTemperature LiquidsVideo input SpecificationsMemo 114 115 BN68-00645A-01