Samsung HP-P5071 manual Ibm Pc / At

Page 79

Notes:

Both screen position and size will vary, depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported:

Video Signal	Resolution	Vertical	Horizontal	Vertical	Horizontal
	(Dot X Line)	Frequency(Hz)	Frequency(KHz)	Polarity	Polarity

	720 X 400	70.087	31.469	P	N
		59.940	31.469	N	N
	640 X 480	72.809	37.861	N	N
	640 X 480	75.000	37.5	N	N
		75.000	37.5	N	N
		85.008	43.269	N	N
		56.250	35.156	N/P	N/P
		60.317	37.897	P	P
	800 X 600	72.188	48.077	P	P
IBM PC / AT		75.000	46.875	P	P
Compatible		85.061	53.674	P	P
Compatible		60.004	48.363	N	N
		60.004	48.363	N	N
	1024 X 768	70.069	56.476	N	N
	1024 X 768	75.029	60.023	P	P
		75.029	60.023	P	P
		84.997	68.677	P	P
	1280 X 1024	60.020	63.981	P	P

•The interlace mode is not supported.

•The PDP operates abnormally if a non-standard video format is selected.

•The table above conforms to IBM/VESA regulations and is based on using the Analog Input.

•“1280 x 1024” is not available in DVI mode.

Notes:

•When this PDP is used as a PC display, 32-bit color is supported.

•Depending on the manufacturer, your PC display screen might appear different. (and depending on your particular version of Windows.)

Check your PC instruction book for information about connecting your PC to a PDP.

•If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.4kHZ (horizontal).

•In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the SOURCE button on the remote control or SOURCE button on the front panel to enter the VIDEO mode. Also, make sure that the PC is connected.

•Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise, random signals might appear).

79

Image 79

Contents Owner’s Instructions Cell Defect WarrantyUser Instructions Screen Image retentionTable of Contents Page General Information Source button Power IndicatorRemote Control Signal Receiver SpeakersAV1, AV2, AV3 Video Input Audio Input L, R Ferrite CoresPC Input RGB in / Audio VIDEO1, S-VIDEO2Remote Control Buttons ˛ MTS button ∑ Reset buttonRemote Control Operation Range ¸ SRS Tsxt buttonSupport Bars Screws Wall Installation InstructionsInstallation Notes Wall Mount BracketHow to assemble the Wall Mount Bracket Wall Installation Instructions Change Angle How to Adjust Mounting AngleFactory default Connecting External Devices to the PDPSpeakers Speaker Dust Cover Installing the SpeakersHow to Assemble the Speakers Standing PartsBlack How to Assemble the Speakers Wall Mount Black How to assemble the Stand-Base Connections Antennas with 75-ohm Round Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVPage Videotape Playback Connecting a VCRViewing camcorder tapes Connecting a CamcorderViewing Tapes Playing DVD Connecting a DVD Player 480i, 480pTo Play DVD To Watch DTV Watching DTVOperation Viewing the Menus and Displays Turning the PDP On and OffViewing the Menus Displaying Status Information Press the Enter button to confirm your choice Plug & Play FeatureEnjoy your watching Plug and Play can only be accessed in the TV mode Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method To View Memorized Channels PIP Mode Using Mute Adjusting the VolumeChanging Channels Setting Up Your Remote Control Remote Control Codes Setting the Signal Source Viewing an External Signal SourceAssigning Names to External input mode Page Picture Control PIP Customizing the PictureUsing Automatic Picture Settings Selecting the Color Tone DNIe Digital Natural Image engine Changing the Screen Size 3Normal 169WidePanorama ZoomStill Freezing the PictureSelecting the PIP Screen Viewing the Picture-in-PictureSelecting an External Signal Swapping the Contents of the PIP and Main Image Changing the Size of the PIP Window Changing the Location of the PIP Image Selecting a Signal Source Antenna or Cable for PIP Changing the PIP Channel Setting the MCCMy Control Color Mode Emerald Green Indian Pink MCC Mode CharacteristicsMCC Custom Settings Resetting the MCC Colors to the Factory Defaults Page Sound Control Customizing the Sound Using Automatic Sound Settings Choosing a Multi-Channel Sound MTS Soundtrack Using the Auto Volume TruSurround XT, SRS and Symbol Setting the TruSurround XTListening to the Sound of the SubPIP Picture Selecting the Internal Mute Channel Control Fine Tuning Channels LNA Low Noise Amplifier Page Connecting a PC and Operation To watch the PC screen Connecting a PCSetting up Your PDP Plug and Play Pin ConfigurationSub Cable How to Set up Your PC Software Windows only IBM PC / AT Adjusting the R.G.B Adjusting the PC ScreenChanging the Position of the Image Picture Automatic Adjustment Picture Quality AdjustmentCoarse Adjustment Fine Tuning Fine Information Page Time Setting Setting the Clock Setting the Sleep Timer Setting the Timers Air Page Function Description Selecting a Menu Language Digital Noise Reduction Selecting the Film Mode Using the Color Weaknees Enhancement Option Setting the Melody Sound Setting the Blue Screen Selecting the Fan Viewing Closed Captions Setting Up Your Personal ID Number PIN Using the V-ChipHow to Enable/Disable the V-Chip How to Set up Restrictions using the TV guidelines 105 106 107 Page Appendix Problem Possible Solution TroubleshootingLiquids Care and MaintenanceIdentifying Problems TemperatureVideo input SpecificationsMemo 114 115 BN68-00645A-01