Samsung HP-P5071 manual Setting Up Your Remote Control

Page 38

Setting Up Your Remote Control

This PDP's remote control can operate almost any VCR, cable box or DVD. After it has been set up properly, your remote control can operate in four different modes :TV , VCR, Cable, DVD or STB. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.

Note : ● The remote control may not be compatible with all DVD Players, VCRs, Cable boxes.

●The remote control can only operate STB made by Samsung.

Setting Up the Remote to Operate Your VCR, Cable box or DVD player

1 Turn off your VCR. (or Cable box, DVD player)

Press the MODE button. The Mode is changed

2 whenever MODE button is pressed.

3 Press the SET button on your TV's remote control.

Using the number buttons on your remote control,

4 enter three digits of the VCR (or Cable box, DVD player) code listed on page 39 of this manual for your brand of VCR (or CATV, DVD). Make sure you enter three digits of the code, even if the first digit is a "0".

(If more than one code is listed, try the first one.)

Press the POWER button on the remote control.

5 Your VCR (or CATV, DVD) should turn on if your remote is set up correctly. If your VCR (or CATV, DVD) does not turn on after setup, repeat steps

2, 3, and 4, but try one of the other codes listed for your brand of VCR (or CATV, DVD).

If no other codes are listed, try each code, 000 through 089 (or Cable box: 000 through 077, DVD player: 000 through 008).

Notes

•When your remote control is in “VCR” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, FF) still operate your VCR.

•When your remote control is in “CATV” or “DVD” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, FF) still operate your VCR.

•You do not need to program the remote for Samsung STBs as the codes are pre-programmed.

38

Image 38

Contents Owner’s Instructions Screen Image retention WarrantyUser Instructions Cell DefectTable of Contents Page General Information Speakers Power IndicatorRemote Control Signal Receiver Source buttonVIDEO1, S-VIDEO2 Video Input Audio Input L, R Ferrite CoresPC Input RGB in / Audio AV1, AV2, AV3Remote Control Buttons ¸ SRS Tsxt button ∑ Reset buttonRemote Control Operation Range ˛ MTS buttonWall Mount Bracket Wall Installation InstructionsInstallation Notes Support Bars ScrewsHow to assemble the Wall Mount Bracket Wall Installation Instructions Connecting External Devices to the PDP How to Adjust Mounting AngleFactory default Change AngleParts Installing the SpeakersHow to Assemble the Speakers Standing Speakers Speaker Dust CoverBlack How to Assemble the Speakers Wall Mount Black How to assemble the Stand-Base Connections Connecting VHF and UHF Antennas Antennas with 75-ohm Round LeadsConnecting Cable TV Cable without a Cable BoxPage Connecting a VCR Videotape PlaybackViewing Tapes Connecting a CamcorderViewing camcorder tapes To Play DVD Connecting a DVD Player 480i, 480pPlaying DVD Watching DTV To Watch DTVOperation Viewing the Menus Turning the PDP On and OffViewing the Menus and Displays Displaying Status Information Plug & Play Feature Press the Enter button to confirm your choiceEnjoy your watching Plug and Play can only be accessed in the TV mode Selecting the Video Signal-source Memorizing the ChannelsStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method To View Memorized Channels PIP Mode Changing Channels Adjusting the VolumeUsing Mute Setting Up Your Remote Control Remote Control Codes Viewing an External Signal Source Setting the Signal SourceAssigning Names to External input mode Page Picture Control Customizing the Picture PIPUsing Automatic Picture Settings Selecting the Color Tone DNIe Digital Natural Image engine Changing the Screen Size Zoom 169WidePanorama 3NormalFreezing the Picture StillViewing the Picture-in-Picture Selecting the PIP ScreenSelecting an External Signal Swapping the Contents of the PIP and Main Image Changing the Size of the PIP Window Changing the Location of the PIP Image Selecting a Signal Source Antenna or Cable for PIP Changing the PIP Channel Setting the MCCMy Control Color Mode MCC Mode Characteristics Emerald Green Indian PinkMCC Custom Settings Resetting the MCC Colors to the Factory Defaults Page Sound Control Customizing the Sound Using Automatic Sound Settings Choosing a Multi-Channel Sound MTS Soundtrack Using the Auto Volume Setting the TruSurround XT TruSurround XT, SRS and SymbolListening to the Sound of the SubPIP Picture Selecting the Internal Mute Channel Control Fine Tuning Channels LNA Low Noise Amplifier Page Connecting a PC and Operation Connecting a PC To watch the PC screenSub Cable Pin ConfigurationSetting up Your PDP Plug and Play How to Set up Your PC Software Windows only IBM PC / AT Adjusting the PC Screen Adjusting the R.G.BChanging the Position of the Image Picture Quality Adjustment Picture Automatic AdjustmentCoarse Adjustment Fine Tuning Fine Information Page Time Setting Setting the Clock Setting the Sleep Timer Setting the Timers Air Page Function Description Selecting a Menu Language Digital Noise Reduction Selecting the Film Mode Using the Color Weaknees Enhancement Option Setting the Melody Sound Setting the Blue Screen Selecting the Fan Viewing Closed Captions Using the V-Chip Setting Up Your Personal ID Number PINHow to Enable/Disable the V-Chip How to Set up Restrictions using the TV guidelines 105 106 107 Page Appendix Troubleshooting Problem Possible SolutionTemperature Care and MaintenanceIdentifying Problems LiquidsSpecifications Video inputMemo 114 115 BN68-00645A-01