Samsung LT-P326W manual Connecting an S-VHS VCR, Connecting a DVI-D Cable

Page 16

I N S TA L L AT I O N

Connecting an S-VHS VCR

Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR. (This connection delivers a better picture as compared to a standard VHS VCR.)

1

To begin, follow steps 1–3 in the previous section to connect the antenna or cable to your VCR and your TV.

AV OUT

2

Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO INPUT jacks on the TV.

AV OUT

3

Connect an S-video cable between the S-VIDEO OUT jack on the VCR and the S-VIDEO INPUT jack on the TV.

AV OUT

An S-video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)

* Each external input source device has a different back panel configuration.

Connecting a DVI-D Cable

1

Connect a DVI-D cable between the

DVI-I INPUT connector on the TV and the DVI connector on the DVD player/ Set-Top BOX.

2

Connect a set of audio cables between the L-AUDIO-R jack

on the TV and the AUDIO OUTPUT jacks on the DVD player/ Set-Top BOX.

Note:If you are using a DVI-D cable to connect

1.Be sure to connect the audio cable (sold separately)as shown above to get normal TV sound. 2.See Appendix “Display Modes ”for supported resolutions.

3.The screen may have shifted to the right or to the left after connecting the cable. The screen must be adjusted on the source(Set-top box).

4.Each external input source device has a different back panel configuration.

English-13

Image 16

Contents LT-P326W Installation Special FeaturesYour New TV OperationPC Display TroubleshootingAppendix List of Features List of PartsRight-Side Panel Buttons Familiarizing Yourself with Your New TV+ VOL Rear Panel Jacks HdmiRemote Control CH and CH Channel UP/DownVOL + and VOL UP / Down / LeftAnynet +100VCR/DVD Functions Installing Batteries in the Remote Control If remote control doesn’t workConnecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsConnecting Cable TV Antennas with 75-ohm Round LeadsSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles All Channels Connecting to a Cable Box that Descrambles Some ChannelsEnglish-10 How to connect Core Connecting HdmiHdmi allows multiple Connecting a VCR Connecting an S-VHS VCR Connecting a DVI-D CableConnecting a DVD Player Connecting a Digital TV Set-Top BoxConnecting a PC TV Rear panelWhat is the Anynet? AnynetAnynet Connecting TV + DVD/VCR Combo Connecting AV Signal Cables Connecting TV + DVD Receiver Connecting AV Signal Cables English-20 Turning the TV On and Off Adjusting the VolumeChanging Channels Viewing the Display Viewing the MenusSetting Up Your Remote Control Setting Up the Remote to Operate Your VCRSetting Up the Remote to Operate Your Cable Box Setting Up the Remote to Operate Your DVD Remote Control Codes Plug & Play Feature Chapter Fo urSelecting the Video Signal-source Memorizing the ChannelsStoring Channels in Memory Automatic Method To select channels overAdding and Erasing Channels Manual Method Labeling ChannelsAlternate method To Set-up Your Channels To Select SourceTo Edit the Input Source Name Using Automatic Picture Settings Customizing the Picture Using Automatic Sound Settings Customizing the Sound UP/DOWNSelecting a Menu Language Setting the Blue Screen Mode Fine Tuning Channels LNA Low Noise Amplifier Viewing Picture-in-Picture PIP SettingsActivating Picture-in-Picture Selecting a Signal Source External A/V for PIP Swapping the Contents of the PIP and Main imageChanging the PIP Channel Changing the Position of the PIP WindowDNIe Digital Natural Image engine MCC My Color Control Easy ControlSkin Tone Green Grass Blue Sky- Reset Detail ControlI2C Intelligent Image Control IBC Intelligent Brightness Control Changing the Screen Size Freezing the PictureAdjusting the Color Tone Setting the TruSurround Xtsrs Tsxt Trademark & Label License NoticeAutomatic Volume Control Reduces the differences in volume level among broadcastersSpecial Sound Options Choosing a Multi-Channel Sound MTS SoundtrackAdjusting the Headphone Sound Selecting the Main or Sub Sound Sub Woofer Setting the Clock Setting the On/Off Timer Auto Power Off Setting the Sleep Timer Sleep timerViewing Closed Captions English-61 Using the V-Chip Setting Up Your Personal ID Number PINHow to Enable/Disable the V-Chip English-64 English-65 To select Mpaa rating, then press the Enter button Press the Enter button to select U or B Color Weakness UP/DOWNSelecting the Melody Using Your TV as a Computer PC Display How to Set up Your PC Software Windows onlyHow to Auto Adjust Adjusting the Screen Quality LEFT/RIGHTChanging the Screen Position To Initialize the Screen Position or Color Settings Identifying Problems Chapter SixMove the computers mouse or press a key on the keyboard English-77 English-78 See if there are Anynet devices connected Make sure that the devices connected support the Anynet Glossary Content Installing the Stand Maintenance of Your LCD TVWall Mount Installation Guide PartsInstallation Dimensions Cleaning and Maintaining Your TV Using Your TV in Another CountrySpecifications Model NameResolution Frequency Display ModesPolarity KHz