Samsung PS-50P4H manual Connecting External Devices to the PDP

Page 11

Installing the Display on the Wall Attachment Panel (continued)

➢The exterior of the PDP may be different than the picture.

	(Assembly and installation of the plastic hanger is the same.)		ENG

1	Remove the screws from the back of the PDP. 2	Use the screws and assemble the plastic
		hanger.

3Tighten the screws of the plastic hanger to the back side of the PDP.

☛◆ Please ask the installers to install the wall mount bracket.

◆Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the PDP on the wall mount bracket.

◆Please avoid catching your fingers while installing and adjusting the angle.

◆Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP.

4Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be separated from wall mount bracket.

PDP panel

Wall attachment panel bracket Wall

ConnectingExternalDevicestothePDP

◆To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions:

1Be sure to remove the safety pins underneath the PDP.

◆If the safety pins are not removed, the angle cannot be adjusted. Any attempt to do so may cause damage to the PDP.

2Pull out the bottom of the PDP (which has been attached to the Wall Mount Bracket) in the direction indicated by the arrows (refer to the illustration) until it clicks.

◆ Using the PDP After Connecting External Devices.

Be sure to secure the PDP by inserting the 2 safety pins after readjusting the angle of the PDP to 0o.

◆For safety, be sure to secure the PDP using the safety pins.

If the safety pins are not used, the PDP may fall, causing serious injury.

11

Image 11

Contents PDP-TELEVISION Cell Defect WarrantyUser Instructions Screen Image retentionVideo Cable DVI Cable Power CordScart Cable Speaker Wire Owner’s InstructionsContents Contents SymbolsYour New Plasma Display Panel For further details about connection, refer to pages 55~59 Actual configuration on your PDP may be differentYour New Plasma Display Panel Infrared Remote Control Angle of the PDP can be up to 15 degrees left/right Inserting the Batteries in the Remote ControlAssembling the Stand-Base Wall Mount Bracket Plastic Hanger Installing the Display on the Wall Attachment PanelConnecting External Devices to the PDP Rear of the PDP Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Using a Coaxial cableMains lead is attached to the rear of your PDP Switching On and OffPlacing in Standby Mode Refer to page 64 for further instructions on plug wiringDisplay the on-screen menu system Becoming Familiar with the Remote ControlRemote control is used mainly to Change channels and adjust the volumeSetting Up Your Remote Control To start the search, press the Enter button Plug & Play FeatureChoosing Your Language If you want to reset this featureSee Storing Channels AutomaticallyYou wish to identify Storing ChannelsManuallyChannel mode Result The Edit menu is displayed Skipping Unwanted ChannelsSkipping unwanted channels Sorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the child lock Activating the Child LockChanging the Picture Standard Displaying InformationCustom Options available in PC, DVI Mode Contrast Adjusting the Picture SettingsCustom PC mode only Colour1 Colour2 Colour3 Adjusting the Picture Settings PC or DVI ModePreset to the PC mode by using the Source button Setting the Picture PC ModeSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneDisplayed Viewing the Channel Scan PictureFreezing the Current Picture Result Main menu is displayedSelecting the Picture Size Positioning and Sizing the screen using ZoomPC to DVI Mode DNIeTM Digital Natural Image engine Selecting the Film ModeSetting the Melody Sound Setting the Blue ScreenResult The main picture and sub picture are interchanged Table of PIP SettingsViewing the Picture In Picture PIP Result The sources are displayed in the following orderButtons Feature Easy functions of remote controlSelecting the Fan Using the Digital NR Digital Noise Reduction FeatureStandard Music Movie Speech Custom Changing the Sound StandardAdjusting the Volume Automatically Adjusting the Sound SettingsSelecting the Internal Mute Setting the TruSurround XTSelecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Absent Power Off Switching the Television On and Off AutomaticallyAV1 AV2 AV3 Viewing an External Signal SourceRedirecting an Input to the External Output Contents Teletext FeaturePress the TTX/MIX button again Displaying the Teletext InformationTo display Press Selecting Display OptionsSelecting a Teletext TeleWeb Feature Option Opening the Home Using the TeleWeb Menu after Displaying the TeleWeb OptionBookmarking the current Entering the bookmarked URLButtonFunction TeleWeb Input Connecting to the External DevicesInput/Output Specification Rear of the TVRear of the TV Side of the TV Connecting to the S-Video InputConnecting to the PC Input Connecting to the DVI InputConnecting to the Component Input To Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System This speaker installation guide is for the 5040 Model How to Install SpeakersHow to Assemble the SpeakersWall Mount Shown at left is a typical screen for Display dialog box Setting up Your PC Software Windows onlyCorrect settings for these two variables are FrequencyHz Input Mode PC/DVIVideo Signal Resolution Vertical Horizontal Pin Configurations Normal picture but no sound Check the volume Power buttonCheck the picture contrast and brightness settings Check the volumeWamer amex Programming the Remote Control for Other Components040, 047, 050, 052, 060, 063, 065, 066, 067 Programming the Remote Control for Other ComponentsAfter Sales Service