Samsung PS-50P4H manual Setting up Your PC Software Windows only

Page 62

Setting up Your PC Software (Windows only)

ENG

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)

On the windows screen, select in the following sequence: Start ➞ Settings ➞ Control Panel.

When the control panel screen appears, click on

Display and a display dialog-box will appear.

Select the Settings tab in the display dialog-box.

The two key variables that apply the television-PC interface are “Resolution” and “Colours”.

The correct settings for these two variables are:

◆ Size (sometimes called “Resolution”) - 1024 x 768 pixels (PS-50P4H)

◆ Colour 32-bitcolour.

Shown at left is a typical screen for “Display” dialog box.

If a vertical-frequency option exists on your display settings dialog box, the correct value is 60 Hz. Otherwise, just click OK and exit the dialog box.

62

Image 62

Contents PDP-TELEVISION Screen Image retention WarrantyUser Instructions Cell DefectOwner’s Instructions Power CordScart Cable Speaker Wire Video Cable DVI CableContents Symbols ContentsYour New Plasma Display Panel For further details about connection, refer to pages 55~59 Actual configuration on your PDP may be differentYour New Plasma Display Panel Infrared Remote Control Angle of the PDP can be up to 15 degrees left/right Inserting the Batteries in the Remote ControlAssembling the Stand-Base Installing the Display on the Wall Attachment Panel Wall Mount Bracket Plastic HangerConnecting External Devices to the PDP Using a Coaxial cable Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Rear of the PDPRefer to page 64 for further instructions on plug wiring Switching On and OffPlacing in Standby Mode Mains lead is attached to the rear of your PDPChange channels and adjust the volume Becoming Familiar with the Remote ControlRemote control is used mainly to Display the on-screen menu systemSetting Up Your Remote Control Plug & Play Feature To start the search, press the Enter buttonIf you want to reset this feature Choosing Your LanguageStoring Channels Automatically SeeStoring ChannelsManually You wish to identifyChannel mode Result The Edit menu is displayed Skipping Unwanted ChannelsSkipping unwanted channels Sorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the Child Lock Activating the child lockDisplaying Information Changing the Picture StandardAdjusting the Picture Settings Custom Options available in PC, DVI Mode ContrastAdjusting the Picture Settings PC or DVI Mode Custom PC mode only Colour1 Colour2 Colour3Setting the Picture PC Mode Preset to the PC mode by using the Source buttonSetting the Picture PC Mode Using the Fine Tune If reception is weak, you can fine tune a channel manuallyResult Main menu is displayed Viewing the Channel Scan PictureFreezing the Current Picture DisplayedSelecting the Picture Size Positioning and Sizing the screen using ZoomPC to DVI Mode Selecting the Film Mode DNIeTM Digital Natural Image engineSetting the Blue Screen Setting the Melody SoundResult The sources are displayed in the following order Table of PIP SettingsViewing the Picture In Picture PIP Result The main picture and sub picture are interchangedEasy functions of remote control Buttons FeatureUsing the Digital NR Digital Noise Reduction Feature Selecting the FanChanging the Sound Standard Standard Music Movie Speech CustomAdjusting the Sound Settings Adjusting the Volume AutomaticallySetting the TruSurround XT Selecting the Internal MuteSelecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Absent Power OffViewing an External Signal Source AV1 AV2 AV3Redirecting an Input to the External Output Teletext Feature ContentsDisplaying the Teletext Information Press the TTX/MIX button againSelecting Display Options To display PressSelecting a Teletext TeleWeb Feature Option Entering the bookmarked URL Using the TeleWeb Menu after Displaying the TeleWeb OptionBookmarking the current Opening the HomeButtonFunction TeleWeb Rear of the TV Connecting to the External DevicesInput/Output Specification InputConnecting to the S-Video Input Rear of the TV Side of the TVConnecting to the DVI Input Connecting to the PC InputConnecting to the Component Input To Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System How to Install Speakers This speaker installation guide is for the 5040 ModelHow to Assemble the SpeakersWall Mount Shown at left is a typical screen for Display dialog box Setting up Your PC Software Windows onlyCorrect settings for these two variables are FrequencyHz Input Mode PC/DVIVideo Signal Resolution Vertical Horizontal Pin Configurations Check the volume Power buttonCheck the picture contrast and brightness settings Normal picture but no sound Check the volumeProgramming the Remote Control for Other Components Wamer amexProgramming the Remote Control for Other Components 040, 047, 050, 052, 060, 063, 065, 066, 067After Sales Service