Samsung PS-50P4H Input Mode PC/DVI, Video Signal Resolution Vertical Horizontal, FrequencyHz

Page 63

Input Mode (PC/DVI)

ENG

Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported:

Video Signal	Resolution	Vertical	Horizontal	Vertical	Horizontal
	(Dot X Line)	Frequency(Hz)	Frequency(KHz)	Polarity	Polarity

	720 X 400	70.087	31.469	P	N
		59.940	31.469	N	N
	640 X 480	72.809	37.861	N	N
	640 X 480	75.000	37.5	N	N
		75.000	37.5	N	N
		85.008	43.269	N	N

		56.250	35.156	N/P	N/P
		60.317	37.897	P	P
	800 X 600	72.188	48.077	P	P

IBM PC / AT		75.000	46.875	P	P
Compatible		85.061	53.674	P	P
Compatible		60.004	48.363	N	N
		60.004	48.363	N	N

	1024 X 768	70.069	56.476	N	N
	1024 X 768	75.029	60.023	P	P
		75.029	60.023	P	P
		84.997	68.677	P	P

	1280 X 1024	60.020	63.981	P	P

(N: Negative / P: Positive)

◆The interlace mode is not supported.

◆The television might operate abnormally if a non-standard video format is selected.

◆“1280 x 1024” is not available in DVI mode.

Notes

◆The PC text quality for PS-50P4His optimum in XGA mode (1024 x 768@60Hz).

◆When this television is used as a PC display, 32-bit colour is supported.

◆Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows). Check your PC instruction book for information about connecting your PC to a television.

◆If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.3kHz (horizontal).

In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the SOURCE button to enter the Video mode. Also, make sure that the PC is connected.

◆When connecting a notebook PC to the television, make sure that the PC screen is displayed through only the television (Otherwise, random signals might appear).

◆When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable connections.

◆The Display Settings Table above complies to the IBM/VESA standards, and based on the analog input.

◆The DVI support mode is regarded as same to the PC support mode.

◆The best timing for the vertical frequency to each mode is 60Hz.

63

Image 63

Contents PDP-TELEVISION Cell Defect WarrantyUser Instructions Screen Image retentionVideo Cable DVI Cable Power CordScart Cable Speaker Wire Owner’s InstructionsContents Contents SymbolsYour New Plasma Display Panel Actual configuration on your PDP may be different Your New Plasma Display PanelFor further details about connection, refer to pages 55~59 Infrared Remote Control Inserting the Batteries in the Remote Control Assembling the Stand-BaseAngle of the PDP can be up to 15 degrees left/right Wall Mount Bracket Plastic Hanger Installing the Display on the Wall Attachment PanelConnecting External Devices to the PDP Rear of the PDP Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Using a Coaxial cableMains lead is attached to the rear of your PDP Switching On and OffPlacing in Standby Mode Refer to page 64 for further instructions on plug wiringDisplay the on-screen menu system Becoming Familiar with the Remote ControlRemote control is used mainly to Change channels and adjust the volumeSetting Up Your Remote Control To start the search, press the Enter button Plug & Play FeatureChoosing Your Language If you want to reset this featureSee Storing Channels AutomaticallyYou wish to identify Storing ChannelsManuallyChannel mode Skipping Unwanted Channels Skipping unwanted channelsResult The Edit menu is displayed Sorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the child lock Activating the Child LockChanging the Picture Standard Displaying InformationCustom Options available in PC, DVI Mode Contrast Adjusting the Picture SettingsCustom PC mode only Colour1 Colour2 Colour3 Adjusting the Picture Settings PC or DVI ModePreset to the PC mode by using the Source button Setting the Picture PC ModeSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneDisplayed Viewing the Channel Scan PictureFreezing the Current Picture Result Main menu is displayedPositioning and Sizing the screen using Zoom PC to DVI ModeSelecting the Picture Size DNIeTM Digital Natural Image engine Selecting the Film ModeSetting the Melody Sound Setting the Blue ScreenResult The main picture and sub picture are interchanged Table of PIP SettingsViewing the Picture In Picture PIP Result The sources are displayed in the following orderButtons Feature Easy functions of remote controlSelecting the Fan Using the Digital NR Digital Noise Reduction FeatureStandard Music Movie Speech Custom Changing the Sound StandardAdjusting the Volume Automatically Adjusting the Sound SettingsSelecting the Internal Mute Setting the TruSurround XTSelecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Absent Power Off Switching the Television On and Off AutomaticallyAV1 AV2 AV3 Viewing an External Signal SourceRedirecting an Input to the External Output Contents Teletext FeaturePress the TTX/MIX button again Displaying the Teletext InformationTo display Press Selecting Display OptionsSelecting a Teletext TeleWeb Feature Option Opening the Home Using the TeleWeb Menu after Displaying the TeleWeb OptionBookmarking the current Entering the bookmarked URLButtonFunction TeleWeb Input Connecting to the External DevicesInput/Output Specification Rear of the TVRear of the TV Side of the TV Connecting to the S-Video InputConnecting to the PC Input Connecting to the DVI InputConnecting to the Component Input Connecting and Using the Home Theater System Connecting the Home Theater SystemTo Display the DVD Home Theater This speaker installation guide is for the 5040 Model How to Install SpeakersHow to Assemble the SpeakersWall Mount Setting up Your PC Software Windows only Correct settings for these two variables areShown at left is a typical screen for Display dialog box Input Mode PC/DVI Video Signal Resolution Vertical HorizontalFrequencyHz Pin Configurations Normal picture but no sound Check the volume Power buttonCheck the picture contrast and brightness settings Check the volumeWamer amex Programming the Remote Control for Other Components040, 047, 050, 052, 060, 063, 065, 066, 067 Programming the Remote Control for Other ComponentsAfter Sales Service