Using handy features
■Using auto setting (Auto setting)
■Correcting the keystone distortion (Keystone)
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations. Control panel
Remote
Control
When the foot adjuster p.25 is used to change the projection angle, the picture will undergo keystone (trap-
Control panel
Remote Control
1Press the AUTO SET button.
The Auto setting menu appears.
2Press the AUTO SET button again.
The menu item is automatically adjusted/set.
For computer input, the 
icon will appear during processing.
FAN TEMP LAMP ON
INPUT | ON / STANDBY |
| ZOOM + |
| MENU |
VOL. - | VOL. + |
AUTO |
|
KEYSTONE | AUTO SET |
| ZOOM - |
ON/
CALLSTANDBY
KEYSTONE AUTO SET
MUTE | FREEZE |
RESIZE
RESIZE
OFF
INPUT
ezoidal) distortion.
This projector is capable of correcting this keystone distortion.
Before correction After correction
FAN TEMP LAMP ON
INPUT | ON / STANDBY |
| ZOOM + |
| MENU |
VOL. - | VOL. + |
AUTO |
|
KEYSTONE | AUTO SET |
| ZOOM - |
ON/
CALLSTANDBY
KEYSTONE AUTO SET
MUTE | FREEZE |
RESIZE
RESIZE
OFF
INPUT
Note
•Auto adjustment/setting may not be performed correctly for input signals other than those supported by the projector p.46 , p.47 .
●Manual adjustment and setting
The menu items vary depending on the input type, as shown in the table below.
Use the 
buttons to adjust the items in the table below, then press the 
button when you are finished. The menu disappears. (The CANCEL button on the remote control also allows you to exit the menu mode.)
Input | Item |
| Description | |
Computer | Phase | Adjust with | to eliminate flicker. | |
|
|
|
| |
| Frequency | Adjust with | to eliminate periodic patterns and | |
Item |
| flickering when many vertical lines appear on the screen. | ||
|
|
| ||
Move left | Move right | |||
Select | ||||
|
|
| ||
Move down | Move up | |||
Clamp 1 Adjusts the clamp pulse position with 
or 
.
Clamp 2 Adjusts the clamp pulse width with 
or 
.
Y/PB/PR |
| Phase | Adjust with | to eliminate flicker. |
| |
|
| Signal format | [ : Enter to setting mode] | [ | : Select one | |
| Item | of the following] | [Apply: | ] |
| |
| 480i(525i)@60Hz/480p(525p)@60Hz/ | |||||
| Select | |||||
| 576i(625i)@50Hz/576p(625p)@50Hz/ | |||||
|
|
|
|
| ||
1Press the AUTO KEYSTONE button.
The Keystone menu appears.
2Press the AUTO KEYSTONE button again.
The keystone distortion is automatically corrected. The 
icon will appear during processing.
●Manual adjustment
Use the 
buttons for keystone adjustment. When the adjustment is finished, press the 
button. The menu disappears. (The CANCEL button on the remote
control also allows you to exit the menu mode.)
Item | Description |
|
|
|
|
Keystone | Shrink button of the screen | Shrink top of the screen |
|
|
|
Notes
•Depending on the amount of keystone adjustment and the content of images, some information may be lost, or the picture quality may suffer.
•Keystone adjustment will not change the shape of the menus.
■Zooming out the images
This equipment is provided with the digital zoom (electric zoom)
You can use the digital zoom in applications where the optical zoom is not applicable due to some physical reasons for installations (Note, however, that digitally zoomed display suffers from some degradation).
Operations
|
| 720p(750p)@60Hz/720p(750p)@50Hz/ | ||
|
| 1080i(1125i)@60Hz/1080i(1125i)@50Hz/ | ||
|
| 1035i(1125i)@60Hz/1152i(1250i)@50Hz | ||
Video | Video mode | [ : Enter to setting mode] | [ | : Select one |
| of the followings] [Apply: | ] |
| |
|
|
| ||
Note
• Moving pictures generated with the DVD software for computers may appear unnatural if it is projected with this projector, but it is not a malfunction.
1Press the ZOOM – button.
Each time the ZOOM – button is pressed, the image is reduced in size.
Control panel
FAN TEMP LAMP ON
INPUT | ON / STANDBY |
| ZOOM+ |
| MENU |
VOL. - | VOL. + |
AUTO |
|
KEYSTONE | AUTO SET |
| ZOOM- |
Remote Control
RESIZE
CANCEL
INPUT
ZOOM+
VOL.- MENU VOL.+
ZOOM-
26 | 27 |