Using handy features (Continued)
■Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the 
button twice (or press the CALL button on the remote control once).
Using the menus
You can call up
■How to use the menus
The menu shown below is only for operation instructions and might be different from the
When the 
button is pressed once, the Setting display menu appears. Pressing it again displays information p.31 . The table below shows what kind
Control panel
FAN TEMP LAMP ON
INPUT | ON / STANDBY |
| ZOOM + |
ON/
CALLSTANDBY
KEYSTONE AUTO SET
actual display.
2. Select a Category
of information is displayed. Press the button (or press the CALL or CANCEL button on the remote control to serve the same purpose) again to dismiss the display.
| MENU |
VOL. - | VOL. + |
AUTO |
|
KEYSTONE | AUTO SET |
| ZOOM - |
MUTE | FREEZE |
RESIZE
RESIZE
OFF
INPUT
Select a category by using 
.
There are following three categorys.
Image adjustment menu p.32
Displays the current adjustments of selected category.
Item shown with gray cannot be adjusted with
“Yes”: displayed, “No”: not displayed
Item | Description | Computer | Y/PB/PR | Video | Camera | |
|
|
|
|
| ||
Input | Input source name | Yes | Yes | Yes | Yes | |
RGB signal mode | RGB input mode [Note 1] | Yes | No | No | No | |
Horizontal resolution (in bits) | Yes | No | No | No | ||
Vertical resolution (in bits) | Yes | No | No | No | ||
Horizontal sync frequency | Yes | No | No | No | ||
Vertical sync frequency [Note 2] | Yes | No | No | No | ||
Sync | Sync signal polarity [Note 3] | Yes | No | No | No | |
Signal format | Y/PB/PR signal format | No | Yes | No | No |
Default setting menu | p.32 |
Display setting menu | p.33 |
Press
to open the menu
3.Adjustments & Settings
of the selected category.
Item
Adjustment/Setting Value 
the current input source.
5. To Finish
Finish via the Status display menu.
Operations
Video mode | Color method of video signal | No | No | Yes | No |
Lamp time | Time of lamp use [Note 4] | Yes | Yes | Yes | Yes |
Version | Firmware version [Note 5] | Yes | Yes | Yes | Yes |
Notes
1: | The mode of supported RGB signals p.46 is shown. |
2: | Same as the refresh rate of the computer signal. |
These marks signify the items can be adjusted/set
by using 
.
These marks signify an item can be switched by
using 
.
This mark signfy that there are options.
Press 
to display a list of options.
To Status display
p.30
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V]. |
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be |
used as a counter of guaranteed lamp time.) When the displayed time approaches 3,000 |
hours, consult with a store about getting a TLPLV2 replacement lamp (sold separately) |
prepared. |
5: [Version] shows the version of the projector’s internal control program. This version is |
referred to for customer service, etc. |
Notes
The figure shows a typical example. As the display may differ depending on the item, use the following pages as a reference.
These marks signify the items can be selected from
the list by using 
.
After an item is selected, apply it by pressing 
.
6. End
• | The displayed information will not be refreshed if the status changes. To refresh the |
| information, dismiss the display, then display it again. |
• | Conducting another operation while information is being displayed dismisses the |
| display. |
4. Back
Note
The menu disappears.
•Menu adjustments and settings are saved when the power is turned off via the ON/ STANDBY button. If the power cable is disconnected before this, or the power goes out, then the data will not be saved.
•You can also use the CANCEL button on the remote control to dismiss the menu display.
30 | 31 |