GE X3.28 F005 A197PAR rec x and y, Partitions overlap, F100 Future expansion points not Nullptr

Page 31

Protocol X DCA
Configuration Guide	GE Energy Services

F005: A197_PAR rec <x> and <y>, Partitions overlap

Cause:

•Records <x> and <y> of the A197_PAR are mapped by the same SRU record and have ranges of addresses that overlap.

Remedy:

•Make sure all partitions that are mapped by the same SRU have address ranges that do not overlap.

F006: A197_COM rec <x>, Only one SRU allowed in Full-Duplex

Cause:

•When in Full-Duplex mode, only one SRU should be mapped.

Remedy:

•Make sure there is only one SRU mapped for A197_COM records that are configured for Full-Duplex mode.

F100: Future expansion points not NULLPTR

Cause:

•There is an interface error between the DCA and the DCA engine.

•The DCA stack is not valid.

Remedy:

•Contact the Customer Service Department and report this error.

•Reboot the RTU.

F101: Unable to find table <table_name>

Cause:

•The DCA was unable to locate one of its required configuration tables.

Remedy:

•Ensure the <table_name> table exists and is comprised of at least one record.

Restricted

A197-0CG-1.00-2

Full	21

Image 31

Contents Allen-Bradley Ansi X3.28 DCA Configuration GuideTrademark Notices Table of Contents Appendix a Messages Logged by the Ansi X3.28 DCA Configuring WIN for the Ansi X3.28 DCASystem Overview List of FiguresList of Tables About this Guide About this GuideWho should use this Guide Additional Documentation Product Perspective OverviewSystem Overview Table Name Description Configuring TablesAnsi X3.28 DCA Configuration Tables Ansi X3.28 DCA Configuration TablesConfiguration Sequence Main Application Configuration Table Parameters Configuring the Main Application Table A197MAINName Range Description Protocol X DCA Communication Port Configuration Table Parameters Configuring Communication Port Table A197COMProtocol X DCA Baud Rate One Character Time ms Character TimesProtocol X DCA SRU Configuration Table Parameters Configuring the SRU Table A197SRUProtocol X DCA Partition Definition Table Parameters Configuring the Partition Definition Table A197PARWord Address System Parameter Unit Type Start Address word address Num. WordsSystem Parameters Table Parameters Configuring System Parameters Table A197SYSCoupler for Allen-Bradley Data Highway System Parameters Address System Parameter Unit Value DefaultConfiguring the Virtual Connection Table A197VC Field Range Description Virtual Connection Configuration Table ParametersWesdac Point Allocation Configuring WIN for the Ansi X3.28 DCA Protocol X DCA A197 Appendix a Messages Logged by the Ansi X3.28 DCAF002 A197SRU rec x, duplicate SRU address y Fatal Error MessagesF004 COM rec x, Interchar Timeout must be less than Rx Time F001 Unable to locate table tablenameF101 Unable to find table tablename F005 A197PAR rec x and y, Partitions overlapF006 A197COM rec x, Only one SRU allowed in Full-Duplex F100 Future expansion points not NullptrF105 Not enough memory F102 Unable to open a channel to WINF103 Unable to create an exchange, name, status=y F104 Unable to spawn process, processnameF109 User data memory overflow F107 Unable to get pointer table nameF108 Not enoughx points, y required Wesdac Point TypesF203 L062COMEXTENSIONS should be initialized F200 Unable to get pointer to COM config record =F201 Unable to create exchange, exchage, status=x F202 Unable to spawn processE110 Unable to open comport, status = Non-Fatal Error MessagesE101 Restart failed for processname E102 Not enough memoryE111 comport unable to set parameters, status = E112 comport unable to set timers, status =E201 Com initialization failed, status = comport E202 Not enough memory E205 Encountered error = x while closing comportE204 a child process has died, suspending I101 Unable to find table A197MAIN, deleting Information MessagesControl Request Return Codes