GE X3.28 manual Control Request Return Codes

Page 39

Protocol X DCA
Configuration Guide	GE Energy Services

I102: Process Restarted, <process_name>

Cause:

•The DCA process <process_name> has restarted.

Effect:

•The ANSI X3.28 DCA will post the information message and continue to run.

A.5 Control Request Return Codes

When processing a disable communications output request, the DCA may not be able to execute the request. If this occurs, the DCA will set the status code returned with the request to the appropriate error code, and negatively acknowledge (NACK) the control request. This section describes the possible status codes returned.

Control Already Active (0x0002)

The control point is already in the requested state. Refer to the Allen-Bradley ANSI X3.28 DCA Functional Specification for more information on whether controls latch on or off, or toggle.

Illegal Point Number (0x0003)

There is no function associated with this output point. Refer to the Allen-Bradley ANSI X3.28 DCA Functional Specification for more information on the number of digital output points required by the DCA and each point's associated functionality.

Command Transmission Failed (0x0080)

The DCA was unable to successfully transmit the command to the associated controller due to poor communications.

Invalid Control Type (0x0081)

The control point selected does not support the requested control type.

Value Out of Range (0x0082)

For setpoints, the requested setpoint value is outside the allowable range.

For R/L controls, the multiplier is too large.

Point Off-Line (0x0083)

The control was not attempted because the selected control point is currently off-line.

Restricted

A197-0CG-1.00-2

Full	29

Image 39

Contents Allen-Bradley Ansi X3.28 DCA Configuration GuideTrademark Notices Table of Contents Appendix a Messages Logged by the Ansi X3.28 DCA Configuring WIN for the Ansi X3.28 DCASystem Overview List of FiguresList of Tables About this Guide About this GuideWho should use this Guide Additional Documentation Product Perspective OverviewSystem Overview Table Name Description Configuring TablesAnsi X3.28 DCA Configuration Tables Ansi X3.28 DCA Configuration TablesConfiguration Sequence Configuring the Main Application Table A197MAIN Main Application Configuration Table ParametersName Range Description Protocol X DCA Communication Port Configuration Table Parameters Configuring Communication Port Table A197COMProtocol X DCA Baud Rate One Character Time ms Character TimesProtocol X DCA SRU Configuration Table Parameters Configuring the SRU Table A197SRUProtocol X DCA Partition Definition Table Parameters Configuring the Partition Definition Table A197PARWord Address System Parameter Unit Type Start Address word address Num. WordsSystem Parameters Table Parameters Configuring System Parameters Table A197SYSCoupler for Allen-Bradley Data Highway System Parameters Address System Parameter Unit Value DefaultConfiguring the Virtual Connection Table A197VC Field Range Description Virtual Connection Configuration Table ParametersWesdac Point Allocation Configuring WIN for the Ansi X3.28 DCAProtocol X DCA A197 Appendix a Messages Logged by the Ansi X3.28 DCAF002 A197SRU rec x, duplicate SRU address y Fatal Error MessagesF004 COM rec x, Interchar Timeout must be less than Rx Time F001 Unable to locate table tablenameF101 Unable to find table tablename F005 A197PAR rec x and y, Partitions overlapF006 A197COM rec x, Only one SRU allowed in Full-Duplex F100 Future expansion points not NullptrF105 Not enough memory F102 Unable to open a channel to WINF103 Unable to create an exchange, name, status=y F104 Unable to spawn process, processnameF109 User data memory overflow F107 Unable to get pointer table nameF108 Not enoughx points, y required Wesdac Point TypesF203 L062COMEXTENSIONS should be initialized F200 Unable to get pointer to COM config record =F201 Unable to create exchange, exchage, status=x F202 Unable to spawn processE110 Unable to open comport, status = Non-Fatal Error MessagesE101 Restart failed for processname E102 Not enough memory E112 comport unable to set timers, status = E111 comport unable to set parameters, status = E201 Com initialization failed, status = comport E205 Encountered error = x while closing comport E202 Not enough memoryE204 a child process has died, suspending I101 Unable to find table A197MAIN, deleting Information MessagesControl Request Return Codes