GE X3.28 manual Information Messages, I101 Unable to find table A197MAIN, deleting

Page 38

	Protocol X DCA
GE Energy Services	Configuration Guide

A.3 Warning Messages

Warning messages indicate recoverable run-time errors, either within the application or through one of the software interfaces. The application will attempt to handle these errors without suspending or jeopardizing the integrity of the system. If a warning message occurs repeatedly, contact the Customer Service Department to report the error.

W001: win_write failed, status = <x>

W101: send_x failed, status = <x>

W102: send_x failing, status = <x>

W103: win_write failing, status = <x> failure condition cleared

W201: Tx Failed, <x> reset - Check Cabling

W202: Error getting a communication buffer"

W203: send_x failing, status = <x>

A.4 Information Messages

Information messages indicate the application is taking some special action based on certain configuration or initialization criteria.

I101: Unable to find table A197MAIN, deleting

Cause:

•The DCA could not find the Main Application configuration table. If the Main Application configuration cannot be located, the application assumes the user does not want it to run.

Effect:

•The ANSI X3.28 DCA will delete itself from the system.

Remedy:

•If the ANSI X3.28 DCA is intended to run, ensure the Main Application configuration table, A197MAIN, exists and is comprised of at least a single record.

A197-0CG-1.00-2Restricted

28	Full

Image 38

Contents Configuration Guide Allen-Bradley Ansi X3.28 DCATrademark Notices Table of Contents Configuring WIN for the Ansi X3.28 DCA Appendix a Messages Logged by the Ansi X3.28 DCAList of Figures System OverviewList of Tables Who should use this Guide About this GuideAbout this Guide Additional Documentation Overview Product PerspectiveSystem Overview Ansi X3.28 DCA Configuration Tables Configuring TablesAnsi X3.28 DCA Configuration Tables Table Name DescriptionConfiguration Sequence Name Range Description Configuring the Main Application Table A197MAINMain Application Configuration Table Parameters Protocol X DCA Configuring Communication Port Table A197COM Communication Port Configuration Table ParametersProtocol X DCA Character Times Baud Rate One Character Time msProtocol X DCA Configuring the SRU Table A197SRU SRU Configuration Table ParametersProtocol X DCA Configuring the Partition Definition Table A197PAR Partition Definition Table ParametersType Start Address word address Num. Words Word Address System Parameter UnitConfiguring System Parameters Table A197SYS System Parameters Table ParametersAddress System Parameter Unit Value Default Coupler for Allen-Bradley Data Highway System ParametersConfiguring the Virtual Connection Table A197VC Virtual Connection Configuration Table Parameters Field Range DescriptionConfiguring WIN for the Ansi X3.28 DCA Wesdac Point AllocationProtocol X DCA Appendix a Messages Logged by the Ansi X3.28 DCA A197F001 Unable to locate table tablename Fatal Error MessagesF004 COM rec x, Interchar Timeout must be less than Rx Time F002 A197SRU rec x, duplicate SRU address yF100 Future expansion points not Nullptr F005 A197PAR rec x and y, Partitions overlapF006 A197COM rec x, Only one SRU allowed in Full-Duplex F101 Unable to find table tablenameF104 Unable to spawn process, processname F102 Unable to open a channel to WINF103 Unable to create an exchange, name, status=y F105 Not enough memoryWesdac Point Types F107 Unable to get pointer table nameF108 Not enoughx points, y required F109 User data memory overflowF202 Unable to spawn process F200 Unable to get pointer to COM config record =F201 Unable to create exchange, exchage, status=x F203 L062COMEXTENSIONS should be initialized E102 Not enough memory Non-Fatal Error Messages E101 Restart failed for processname E110 Unable to open comport, status =E201 Com initialization failed, status = comport E112 comport unable to set timers, status =E111 comport unable to set parameters, status = E204 a child process has died, suspending E205 Encountered error = x while closing comportE202 Not enough memory Information Messages I101 Unable to find table A197MAIN, deletingControl Request Return Codes