Black & Decker Li4000, 90564630 instruction manual Troubleshooting

90564630 li4000 revision.qxd:??????-00 BDL500 laser 5/25/10 7:45 AM Page 10

• Slide screw holder arm back towards screwdriver bit. Ensure screwdriver bit tip and

screw head are fully engaged. (figure H)

Troubleshooting

• At this time the screw is being held securely to the screw holder carrier by means of an

internal magnet. Note: Magnet will not work on non-ferrous screws.

• Ensure unit is set for driving screws in the forward position.

• While driving the screw, the screw holder carrier and arm will retract allowing the screw

head to be driven to its desired depth (figure I).

• After use, return screw holder arm back into its storage position to protect screw holder

from damage.

Screw driving Notes:

•Do not use double ended screwdriver bits.

•Do not use screwdriver as a pry bar in any position.

•To avoid screwdriver being turned on accidentally, do not carry in your pocket.

LED LIGHT

A light (5) is built-in to the screwdriver above the spindle (6). To use the light without the spindle turning, place the forward / reverse selector (2) in the neutral position.

DRILLING

•Insert the appropriate hex shank drill bit.

•Select the largest screw icon on the clutch collar for maximum torque.

•Select forward rotation.

NOTE: When drilling, the bit may become disconnected from the spindle upon withdrawing it from the material. Should this occur, the bit can be removed by re-inserting the hex shank into the spindle and running the tool in the reverse direction.

GENERAL DRILLING TIPS

• This tool is not recommended for drilling in masonry.
•	Use sharp drill bits only.
• Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and
	should be pulled out frequently when drilling to clear chips from the flutes.
•	Support and secure work properly, as instructed in the safety Instructions.

Problem	Possible Cause
• Battery will not charge.	• Charger not plugged into
	a working outlet.

	• Surrounding air temperature
	too hot or too cold.
• Tool will not drill.	• Torque adjustment collar in
	wrong position.
• Screws stripping.	• Torque adjustment collar
	setting too high.

•Screws not fully seated. • Torque adjustment collar setting too low.

•Screw holder not holding • Screw is non-ferrous. screw.

Possible Solution

•Plug charger into a working outlet. Refer to “Important Charging Notes” for more details.

•Check current at receptacle by plugging in a lamp or other appliance.

•Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

•Move charger and tool to a surrounding air temperature of above 40 degree F (4,5°C) or below 105 degree F (+40,5°C).

•Move collar position to largest screw icon.

•Move collar position to

a smaller screw icon.

•Move collar position to a larger screw icon.

•Use ferrous screw.

• Use appropriate and required safety equipment, as instructed in the safety instructions.

• Secure and maintain work area, as instructed in the safety instructions.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting

but not so much as to stall the motor or deflect the bit.

• Hold the tool firmly to control its twisting action.

• DO NOT CLICK THE TRIGGER OF A STALLED TOOL OFF AND ON IN AN ATTEMPT

TO START IT. DAMAGE TO THE TOOL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through last

part of hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce

jamming.

• Make sure switch turns tool on and off.

WARNING: It is important to support work properly and to hold the tool firmly to prevent loss of control which could cause personal injury.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

THE RBRC™ SEAL The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the

lithium-ion battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent lithium-ion batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent lithium-ion batteries. Help protect our environment and conserve natural resources by returning the tool to an authorized Black & Decker service center for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or call

1-800-8-BATTERY.

10 11