Sony KP 43T90, KP 61V90, KP-48V90, KP-53S76, KP 53V90 Connecting a DVD Player Upper illustration

Page 19

Connecting a DVD Player (Upper illustration)

Disconnect all power sources before making any connections.

(Rear of projection TV)

Using an AUDIO and S VIDEO cables, connect AUDIO and S VIDEO IN on the projection TV to AUDIO and S VIDEO OUT on the DVD Player (White-AUDIO Left, Red- AUDIO Right).

Connecting a DVD Player with component video output connectors (Lower illustration)

1 Using an AUDIO cable, connect AUDIO of

			AUX
			TO
			CONVERTER
S VIDEO		IN
		IN
	VIDEO 1 VIDEO 3	VIDEO 4	VHF/UHF
			VHF/UHF
			OUT
S VIDEO			AUDIO
			(VAR/FIX)
VIDEO		Y
L		PB	L
(MONO)			(MONO)
			AUDIO
R		PR	R
AUDIO-R	COMPONENT
AUDIO-L

DVD

LINE OUT	S VIDEO OUT	S-LINK	DIGITAL OUT
R–AUDIO 1–L VIDEO			OPTICAL	COAXIAL

Audio/S video outputs

LINE OUT on the DVD Player to AUDIO of

VIDEO 4 IN on the projection TV (White-

AUDIO Left, Red-AUDIO Right).

2 Using three yellow VIDEO cables, connect

Y, PB, and PR of COMPONENT VIDEO

OUT on the DVD Player to Y, PB, and PR of

VIDEO 4 IN on the projection TV.

Notes:

(Rear of

projection

TV) AUDIO-L AUDIO-R

RK-74A (not supplied)

YC-15V/30V (not supplied)

RK-74A

AUX

(not

supplied) TO

CONVERTER

Connect the DVD Player directly to the projection TV. Connecting the DVD Player through other video equipment will cause unwanted picture noise.

•Since the high quality pictures on a DVD disc contain a lot of information, picture noise may appear. In this case, adjust “Noise Reduction” in the Video menu. (see “Noise Reduction” on page 26)

•Some DVD Player terminals may be labeled differently. If so, connect as follows: Connect Y (green) to Y.

Connect PB (blue) to CB, Cb or B-Y. Connect PR (red) to CR, Cr or R-Y.

•This projection TV does not support progressive scan DVD players output. Please use the interlaced output.

	IN
VIDEO 1 VIDEO 3	VIDEO 4		VHF/UHF
		OUT	VHF/UHF
		OUT
S VIDEO		AUDIO
		(VAR/FIX)				DVD
VIDEO	Y					DVD
VIDEO	Y
L	PB	L	LINE OUT		S VIDEO OUT	COMPONENT VIDEO OUT			S-LINK	DIGITAL OUT
L	PB	(MONO)	R–AUDIO 1–L	VIDEO		Y	B-Y	R-Y		OPTICAL	COAXIAL
(MONO)		(MONO)	R–AUDIO 1–L	VIDEO		Y	B-Y	R-Y		OPTICAL	COAXIAL
AUDIO		AUDIO
R	PR	R
COMPONENT

Y
PB	VMC-10HG
PR	(not supplied)
	(not supplied)

15

Image 19

Contents Projection TV Precaucion Code SET Remote ControlTable of Contents Welcome Using This ManualSafety PrecautionsInstalling Use Important SafeguardsInstallation Damage Requiring Service ServiceLightning For Safety Vertical Installing and Connecting the Projection TVCarrying Your Projection TV Installing the Projection TV Recommended viewing areaMaking Connections Connector TypesCable and antenna Connecting a cable boxCable box and cable Cable or antennaConnecting a VCR and projection TV to a cable box Connecting a cable TV systemAntenna to a VCR Video Connecting a satellite receiver SAT Connecting a satellite receiver Connecting a camcorder Connecting a DTV digital television receiverConnecting a DVD Player Upper illustration Connecting an audio system Control S OUT on the projection TV Connecting a Sony Sava series speaker systemInserting the batteries Basic Set UpUsing the Remote Control Setting Up the Projection TV AutomaticallyPress Channel + to preset channels automatically Adjusting the Convergence Automatically Flash FocusTo perform Auto SET UP again Press Volume to continueWatching the TV Using Your New Projection TVSpeed Surf Jump TV, Video 1, Video 2, Video 3 and VideoBBE, Surround, Simulated and Effect Off. see Effect on XDS Extended Data ServiceCaption Vision No displayWatching Two Programs at One Time PIP Using the Yellow Labeled Buttons for PIP OperationsSnowy channel. see Channel Skip If one of the pictures received throughPIP is snowy, the entire screen may Become unstable. In this case, erasePress V or v to highlight the desired option Adjusting Your SET UP menusLearning Menu Selection To exit from the menus at any timeTo restore the factory settings Using the Video MenuTo select the Video menu To select the Audio menu Using the Audio MenuAudio Out SpeakerSava SP Control Daylight Savings Using the Timer MenuTo select the Timer menu TimerTo select the Channel Set Up ch menu Ch Using the Channel Set Up MenuFavorite Channel will not function with AUX input Auto Program Skip/AddCable Setting Favorite Channel manually Setting and SelectingFavorite Channel Press Menu when you are done Using Favorite ChannelChanging Favorite Channel choices Control Using the Set Up MenuTo select the Set Up menu ParentalFlash Focus Video LabelActivating the Parental Control Feature Using the Parental Control FeatureTo deactivate the Parental Control FeatureSelecting a Custom Rating To unlock the Parental Control feature temporarilyPress V or v to select Custom, First, select a TV rating Press V or v to select Movie Rating Second, select a movie ratingCanada Changing the Password Ratings in U.S.A Enter a new four digit password using the 0-9 buttonsIf you have forgotten your password What the Ratings MeanTV ratings Movie ratingsCanadian English Language ratings Ratings in CanadaTV-NR rating is shown as Unrated in the menu About the extenders of U.S. TV ratingsCanadian French Language ratings VCR manufacturer code numbers Setting the Manufacturers CodeIf the remote control doesn’t work Operating Video EquipmentTo operate video equipment MDP manufacturer code numbersDVD Player manufacturer code NumbersPress TV FUNCTION. Then use Operating a Cable Box or Satellite Receiver SATManufacturer code numbers cable box To operate the cable box or satellite receiver SATSound TroubleshootingCannot receive any channels Specifications Fixed/Variable IndexVCR