Sony KP 53V90 Operating a Cable Box or Satellite Receiver SAT, Press TV FUNCTION. Then use

Page 53

Operating a Cable Box or Satellite Receiver (SAT)

Setting the Manufacturer's Code

You can program the supplied remote control to operate a cable box or satellite receiver.

Press CODE SET, SAT/CABLE (FUNCTION), and the 0-9 buttons to enter the manufacturer’s code number (see the following chart), then press ENTER.

For example, to operate a Sony satellite receiver:

CODE SET

FUNCTION

 

ENTER

SAT/CABLE

0

 

8

1

Manufacturer code numbers

To operate the projection TV

(satellite receiver)

 

Press TV (FUNCTION). Then use the

 

 

projection TV control buttons to control the

Manufacturer

Code number

projection TV.

Sony

801 (preset code for

 

 

remote control)

 

General Electric

802, 808

Tips z

Hitachi

805

• If more than one code number is listed, try entering

Hughes

804

them one by one until you come to the correct code

Panasonic

803

for your equipment.

RCA/PROSCAN

802

 

Toshiba

806, 807

• If you enter a new code number, the code number

 

 

you previously entered at that setting is erased.

 

 

Manufacturer code numbers (cable box)

Manufacturer

Code

Hamlin/Regal

222, 223, 224, 225, 226

Jerrold/G.I

201, 202, 203, 204, 205,

 

222, 206, 207, 208, 218

Oak

227, 228, 229

Panasonic

219, 220, 221

Pioneer

214, 215

Scientific Atlanta

209, 210, 211

Tocom

216, 217

Zenith

212, 213

To operate the cable box or satellite receiver (SAT)

1Press SAT/CABLE (POWER) [Green Button] to turn on/off the cable box or satellite receiver.

2Press SAT/CABLE (FUNCTION).

3For other operations, refer to the operating instructions that come with the equipment.

The GUIDE and INDEX (blue-labeled) buttons can be used only with a satellite receiver.

If the remote control doesn’t work

•Try repeating the set up procedures using the other codes listed for your equipment.

•In some rare cases, you may not be able to operate your equipment with the supplied remote control. In this case, use the equipment’s own remote control unit.

•Whenever you remove the batteries — to replace them, for example — if too much time is taken, the code numbers may revert to the factory setting and must be reset.

49

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Projection TV Precaucion Code SET Remote ControlTable of Contents Welcome Using This ManualInstalling PrecautionsSafety Use Important SafeguardsInstallation Lightning ServiceDamage Requiring Service For Safety Carrying Your Projection TV Installing the Projection TV Installing and Connecting the Projection TVRecommended viewing area VerticalMaking Connections Connector TypesCable box and cable Connecting a cable boxCable or antenna Cable and antennaAntenna to a VCR Connecting a cable TV systemConnecting a VCR and projection TV to a cable box Video Connecting a satellite receiver SAT Connecting a satellite receiver Connecting a camcorder Connecting a DTV digital television receiverConnecting a DVD Player Upper illustration Connecting an audio system Control S OUT on the projection TV Connecting a Sony Sava series speaker systemUsing the Remote Control Basic Set UpSetting Up the Projection TV Automatically Inserting the batteriesTo perform Auto SET UP again Adjusting the Convergence Automatically Flash FocusPress Volume to continue Press Channel + to preset channels automaticallySpeed Surf Using Your New Projection TVWatching the TV Jump TV, Video 1, Video 2, Video 3 and VideoCaption Vision XDS Extended Data ServiceNo display BBE, Surround, Simulated and Effect Off. see Effect onWatching Two Programs at One Time PIP Using the Yellow Labeled Buttons for PIP OperationsPIP is snowy, the entire screen may If one of the pictures received throughBecome unstable. In this case, erase Snowy channel. see Channel SkipLearning Menu Selection Adjusting Your SET UP menusTo exit from the menus at any time Press V or v to highlight the desired optionTo select the Video menu Using the Video MenuTo restore the factory settings To select the Audio menu Using the Audio MenuSava SP Control SpeakerAudio Out To select the Timer menu Using the Timer MenuTimer Daylight SavingsFavorite Channel will not function with AUX input Ch Using the Channel Set Up MenuTo select the Channel Set Up ch menu Cable Skip/AddAuto Program Favorite Channel Setting and SelectingSetting Favorite Channel manually Changing Favorite Channel choices Using Favorite ChannelPress Menu when you are done To select the Set Up menu Using the Set Up MenuParental ControlFlash Focus Video LabelActivating the Parental Control Feature Using the Parental Control FeatureTo deactivate the Parental Control FeaturePress V or v to select Custom, To unlock the Parental Control feature temporarilySelecting a Custom Rating First, select a TV rating Press V or v to select Movie Rating Second, select a movie ratingCanada Changing the Password If you have forgotten your password Enter a new four digit password using the 0-9 buttonsWhat the Ratings Mean Ratings in U.S.ATV ratings Movie ratingsTV-NR rating is shown as Unrated in the menu Ratings in CanadaAbout the extenders of U.S. TV ratings Canadian English Language ratingsCanadian French Language ratings If the remote control doesn’t work Setting the Manufacturers CodeOperating Video Equipment VCR manufacturer code numbersDVD Player manufacturer code MDP manufacturer code numbersNumbers To operate video equipmentManufacturer code numbers cable box Operating a Cable Box or Satellite Receiver SATTo operate the cable box or satellite receiver SAT Press TV FUNCTION. Then useSound TroubleshootingCannot receive any channels Specifications Fixed/Variable IndexVCR
Top Page Image Contents