Access Point Connection Setting, Display

When you experience problems with settings

Access Point Connection Setting

Failed to connect to the access point.

A conflict with another device occurred.

Do you want to configure Access Point Connection

Setting again ?

YesNo

	Display		Check the following
	A conflict with another		≥ Please wait a few moments,
	device occurred.		and then try again.

			≥ Setting of the Wireless
			router (Access point) for
	A time out error occurred.		MAC Address etc.
			≥ The signal may be weak.
			Using the included USB
			extension cable, adjust the
			extension cable, adjust the
			position of the Wireless LAN
			Adaptor.
	An authentication error or a		≥ The SSID and the
	An authentication error or a		encryption key of the
	time out error occurred.		Wireless router (Access
			point).
			≥ Please wait a few moments,
			and then try again.

			≥ Connection of Wireless LAN
	A device error occurred.		Adaptor
	A device error occurred.		If there is no improvement in
			symptom, contact our
			Customer Service Center.

Network Easy Setting (Connection Check)
Network Easy Setting (Connection Check)

	Complete.
	1. LAN cable connection	: Fail
	2. IP address setting	: Fail
	3. Connection to gateway	: Fail

	LAN cable is not connected.
	Please check the connection.
	Select “Yes” and press [OK] to check network
	connection again. Select “No” and press [OK]
	to finish Network Easy Setting.

	Yes		No
	OK

	Display			Check the
	Display			following
				following
	1. LAN cable connection or		: Fail	≥ Connection of
	Connection to access point		: Fail	the LAN
	Connection to access point			the LAN
	2. IP address setting		: Fail	cables (> 10)
	2. IP address setting		: Fail
	3. Connection to gateway		: Fail

1.	LAN cable connection or	: Pass	≥ Connection
Connection to access point		: Pass	and settings
Connection to access point			and settings
2.	IP address setting	: Fail	of the hub
2.	IP address setting	: Fail	and router
			and router
3.	Connection to gateway	: Fail	≥ Settings of
			“IP Address/
1.	LAN cable connection or		“IP Address/
1.	LAN cable connection or	: Pass	DNS
Connection to access point		: Pass	DNS
Connection to access point			Settings”
			Settings”
2.	IP address setting	: Pass	(> 29)
3.	Connection to gateway	: Fail

Network Easy Setting (Internet Connection Check)

Network Easy Setting (Internet Connection Check)				Settings
	Complete.			Settings
	Complete.
	- Connection to the Internet :	Fail(Error code: B019)


	Failed the connection test.			&
	Cannot find the server.(Error code: B019)			&
	Cannot find the server.(Error code: B019)			Connections
	OK			Connections
	Please refer to the operating instructions for the cause
	of the error and the solution for it.
	Press [OK].

	Display		Check the following
	Cannot find the server.		≥ Settings of “IP Address/DNS
	(Error code: B019)		Settings” (> 29)

			≥ The server may be busy or the
	Failed to connect to		service may have been
	Failed to connect to		suspended. Please wait a few
	the server.		suspended. Please wait a few
	the server.		moments, and then try again.
	(Error code: B020)		moments, and then try again.
	(Error code: B020)		≥ Settings of “Proxy Server
			≥ Settings of “Proxy Server
			Settings” (> 29) and the router

≥Refer to the operating instructions of the hub or router.

≥You can perform this setup anytime by selecting “Network Easy Setting” in the Setup menu. (> 29)

≥You can redo these settings individually using “Network Settings”. (> 29)

≥If you experience problems after selecting “Wireless”, you should first confirm the setting of your Wireless router (Access point) connected to your home network using your PC.

≥After performing network settings on this unit, the settings (encryption level, etc.) of the Wireless router (Access point) might change. When you have trouble getting online on your PC, perform the network settings on your PC in accordance with the settings of Wireless router (Access point).

VQT2H76

When you experience problems with settings